Cover Recommendations for a B&W Companion 5th Wheel Trailer Hitch

Question

Question:

Can you recommend a cover for this hitch?

asked by: Bill

0

Expert Reply:

We do have some 5th wheel hitch covers that you could potentially use. First we have # RP30055 which is designed to cover just the head of the hitch. It is 18 inches by 28 inches. And we have cover # CA80116. This cover is meant to cover the whole hitch. It is 18 inches tall 24 inches long and 24 inches wide (at the base).

expert reply by: Michael H

0

Answer 1

We actually have two Retrax tonneau covers available for your 2022 GMC Sierra 3500 with the 8 foot bed. Both of these will definitely be great retractable options for keeping your hitch safe and secure from the elements, but the RetraxPRO XR…

view full answer...

Answer 2

The offset ball that you will need for your B&W Turnoverball gooseneck trailer hitch is part #BWGNXA4085. This 4" Offset Ball was designed to work with your hitch and has a square ball base to prevent ball from turning in hitch…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 8

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 9

For your 4x6 utility trailer, I recommend using the Taskmaster 4.80R12 Radial Trailer Tire part #TT48012C. This tire has a radial ply construction which will be better for the longer highway trips you intended to make. It has a load range C rating…

view full answer...

Answer 10

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 11

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Cover Recommendations for a B&W Companion 5th Wheel Trailer Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching