Can Grille Br Removed From Furrion RV Soundbar

Question

Question:

How do you remove the face plate from the Furrion sound bar in a camping trailer?

asked by: Rob H

1

Helpful Expert Reply:

I went to the warehouse and pulled one of the # FSB24SA2C-BL speakers.

The outer body is molded and the speaker grille is built into the outer shell of the cabinet and cannot be removed. I have seen some speakers that have a removable grille but this soundbar does not have that feature. I am afraid the grille or speaker cabinet would be damaged if the grille were removed.

expert reply by: Jeffrey L

1

Answer 1

It sounds like you have already tried this. But just to make sure we have covered the bases, to reset the unit back to factory settings you will need to press and hold MODE button for more than 6 seconds. To remove the Furrion RV Soundbar w/…

view full answer...

Answer 2

We have just what you need. The part #AKEBRK-7-SA is a set of 7,000 lb capacity rebranded Axle Tek self-adjusting brake assemblies like what you currently have. These would be an exact replacement and will work well.

view full answer...

Answer 3

You may be able to combine a torsion lift kit and larger tires and wheels to get you close to the 4" lift that you are looking for. Currently there is not a torsion lift kit that will raise your 2011 Forest River Rockwood 8244S that much.…

view full answer...

Answer 4

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 5

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 6

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Can Grille Br Removed From Furrion RV Soundbar

Product Page this Question was Asked From

Continue Researching