Install Video and Instructions for Draw Tite Hitch 76025

Question

Question:

Do you have a video or instructions on your web site or available via email for installing hitch receiver 76025? Thanks,

asked by: John B

0

Expert Reply:

I attached a link to the install video for the Draw Tite hitch part # 76025 as well as a link to the install instructions for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Draw Tite hitch part #76025 that you referenced is a confirmed fit for your 2012 Honda Odyssey. It would install exactly the same as the video that shows the hitch installed on a 2014 Honda Odyssey. I checked the install instructions and there…

view full answer...

Answer 2

The Draw-Tite Trailer Hitch Receiver, #76025, that fits the 2013 Honda Odyssey will give you more clearance than the Draw-Tite #75270 hitch. The #76025 hitch sits higher up under the bumper which will give you more ground clearance. In our…

view full answer...

Answer 3

The primary difference is a matter of numbers. When installed, the Draw-Tite Class III #76025 will sit so the inside top edge of the receiver tube sits about 13 inches above the ground, and the receiver tube will sit under the bumper so that the…

view full answer...

Answer 4

With the use of a cargo carrier a transmission cooler is not normally used, but a cooler will prolong the life of a transmission towing or not so it's a great idea for your 2014 Honda Odyssey. We installed the Derale part #D13502 on a 2014…

view full answer...

Answer 5

The Draw-Tite Max-Frame Trailer Hitch Receiver #76025 referenced in your question is confirmed to fit your 2017 Honda Odyssey. It features a sleek, hidden crosstube design, but this feature does require more of an in-depth installation when…

view full answer...

Answer 6

Just to make sure we are accurate on the actual rise you may need, lets cover some basics. With the tow vehicle parked on level ground, measure from the ground to the top of your hitch receiver opening. Then, with the trailer level, measure from…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Reese and Draw-Tite products are manufactured by the same parent company, this means that the #26102 and #26002, Dual Cam Sway Control systems are the same, but there is a difference in the generations of the systems. The older systems had…

view full answer...

Answer 9

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75600 for your 2018 BMW X5 does not have a designated mounting location for your 4-way trailer connector. So, for the ZCI Circuit Protected Vehicle Wiring Harness w/…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...