Roof Rack Fit Recommendation for 2005 Honda CR-V

Question

Question:

do u have a rack for this car and what is the $ and how easy is it to put on

asked by: Bill

0

Expert Reply:

The Rhino Rack part # RRRVP01 is a confirmed fit for your 2005 Honda CR-V. It installs by attaching to the fixed mounting points of the roof. To put it on is very easy. You just have to thread the bolts through the bolt hole in the roof.

Price is available at the link below.

expert reply by: Jameson C

0

Answer 1

You will want to make sure you get a roof rack that is designed for your 2005 CR-V. When traveling you want the equipment you use to be dependable. For a roof rack I recommend the Rhino-Rack RVP Series Roof Rack, part #RRRVP01. This roof rack has…

view full answer...

Answer 2

The Rhino Rack #RRRVP01 RVP roof rack is a confirmed fit for your 2005 Honda CR-V. When installed, the crossbar spread (center to center distance between front and rear crossbar) will be 33 inches. The SportRack #SR9035 roof cargo basket is…

view full answer...

Answer 3

The weight capacity of the #TH712200 crossbars themselves is 220 lbs. The weight capacity of the whole set up (the #TH460R feet and the #THKIT3050 ) with the capacity of the roof factored in is 150 lbs. Any roof rack system will only be as strong as…

view full answer...

Answer 4

There is a way to attach a roof rack to your 2005 Honda CR-V with a naked roof, and the correct fit for your CR-V is the following: - Rhino-Rack RVP Roof Rack #RRRVP01

view full answer...

Answer 5

As long as the crossbars are in good condition, you can reuse the Round 48 Inch Crossbars for Yakima Roof Rack Systems #Y00408 on the 2005 Honda CR-V with naked roof. Yakima recommend the 58 Inch Round CrossBars for the 2005 Toyota Highlander, so I…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Roof Rack Fit Recommendation for 2005 Honda CR-V

Continue Researching