Inner Dimensions for the NOCO Battery Tray # 329-BT27S

Question

Question:

would this fit a standard marine battery

asked by: Mike C

1

Helpful Expert Reply:

Battery sizes can vary a bit but the one you have for your trolling motor should work fine with the NOCO Battery Tray # 329-BT27S that you referenced. You would want to measure the dimensions of your battery to be certain though.

The internal dimensions of the tray on this measures 12-7/8 long x 7-1/8 wide wide.

expert reply by: Jameson C

1

Answer 1

The Battery Tray with Strap #329-BT27S is compatible with batteries up to 13-1/8" long x 8-5/16" wide. That is meant for 1 battery that size. It will most likely work for your 2 battery set-up, it just may not be perfect since it is a…

view full answer...

Answer 2

So the internal dimensions of the Torklift box part #TLA7700L that you referenced are 11-3/4 inches deep which is another way of saying tall. So since your battery is 11.02 inches tall this would easily be compatible. Since your width is 7.28 inches…

view full answer...

Answer 3

We sure do! The ring terminal you will need to connect your 6 gauge wire to the 2-Pole Socket Connector #PK12801 is the Spectro Ring Terminal - 6 Gauge - 3/8" Ring ID - Copper - Zinc Plated - Qty 1 #SWC57016Z. Now to crimp this heavy duty ring…

view full answer...

Answer 4

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

If you're looking for a replacement Kwikee tray then I recommend the Kwikee RV Battery Tray - 25-1/8" Long x 24-1/2" Wide #LC366331 which should allow you to place the batteries side by side. If instead you're just looking for a…

view full answer...

Answer 7

The dimensions of a Group 27 battery are 12 inches long by 6-5/8 inches wide by 9-3/16 inches tall so for a box that can carry two of them we have the TorkLift PowerArmor Locking Battery Box #TLA7708R which has dimensions of 26-3/4" long x…

view full answer...

Answer 8

The great things about the 50MM Nev-R-Lube Bearing for 8,000-lb Dexter Axles part #31-71-3 is they do not require grease. They are a bearing, race and seal built into one pre-greased from the factory. You can use a very small amount of anti-seize…

view full answer...

Answer 9

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life so there is typically no…

view full answer...

Answer 10

There are two ways to wire up two batteries. One way doubles the volts of the two batteries and the other keeps the same amount of volts. In parallel the voltage stays the same and in series it is doubled. Check out the diagram for more info.

view full answer...

Answer 11

Easiest way will be to use the winch plate mount part #BDW20291 that you mentioned but attach it to the floor of the trailer at the very front to a crossmember of the frame. To mount in the V area of the A-frame is possible but it would require quite…

view full answer...

Answer 12

You can mount toolbox #DZ76 pretty much anywhere that you have space and a structure to which to mount it. Based on the picture you have submitted it looks like it can mount exactly where you want it. I do not foresee any problems with this…

view full answer...

Inner Dimensions for the NOCO Battery Tray # 329-BT27S

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching