Adding a 7-Way, Battery, and Interior LED Lights for an Enclosed Trailer
Question:
I have a 6x12 Wells Cargo enclosed trailer Id like to add a battery and LED interior lights to. It just has the basic 4 flat wiring. Would it be benificial to ad a 7 way connector to the trailer to maintain the battery while towing? What is my best course of action and what parts would you suggest I need to purchase to light my trailer. Tow vehicle is a Toyota Tundra with both 4 and 7 way trailer connections.
asked by: Steve
Helpful Expert Reply:
It would be a good idea to add a 7-Way trailer connector such as # H20042 to the trailer so you can utilize the 12 volt circuit on the Toyota Tundra's 7-Way connector to provide a maintenance charge to a trailer mounted battery.
On the above 7-Way the green wire is running lights, brown is right turn and brake lights, black is 12 volt that you will run to the battery on the trailer, red is left turn/brake lights, and white is ground. Usually on a 4-Way you will have white as ground, brown and running lights, yellow as left turn/brake, and green as right turn/brake.
The unused wires on the 7-Way can be capped off.
You will also need a battery box such as # 329-HM300BKS which accepts group 24 batteries. The group indicates the size and if you go to an auto parts store to get a battery just make sure you ask for one with a group number that matches what the box can accept.
For lights you can get several of # 277-000343 which is a surface mount light. The more you use the brighter it will be. I recommend running power from the battery to a switch, # PK34513, and then from the switch to the lights.
Products Referenced in This Question
Gustafson 12V RV LED Puck Light - Recessed - 3-1/2" Diameter - White
- RV Interior Lights
- Puck Light
- Warm White
- No Switch
- Recessed Mount
- LED Light
- 12V
- 3 Inch Diameter
- White
- Gustafson Lighting
more information >
7-Way Molded Trailer Wire Connector - 3' Long
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 7 Round - Blade
- Hopkins
more information >
Pollak Light-Duty Toggle Switch - On-Off - 12 Volt - 10 Amp - 6" Wire Leads
- Accessories and Parts
- Wiring
- Switches
- Toggle Switch
- 10 Amp
- Pollak
more information >
Product Page this Question was Asked From
Breakaway Kit Replacement 12 V Battery
- Accessories and Parts
- Trailer Breakaway Kit
- 12V Battery
- Hopkins
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Q&A: Mounting the Aluminum A-Frame Trailer Tongue Toolbox to the A-Frame of The Trailer
- Article: Rooftop Cargo Carriers
- Q&A: Hitch Extension for Towing a Boat on a Truck with an In-Bed Truck Camper
- Q&A: Can I Use Both the 7-Way and 4-Way Connectors at the Same Time on a 2015 Chevrolet Silverado
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: How Do I Measure the Drop Distance on a Trailer Drop Axle?
- Q&A: Reese Extension/Reducer # RP45292 Compatibility with Class V Factory Hitch on 2013 Ram 2500
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Replace or Install an RV Roof Vent
- Article: 2023 Best Gifts for Haulers & Towers