Replacement Hardeware Kit for a Curt Receiver Hitch.

Question

Question:

Hello E-Trailer, Im going to reinstall my Curt C11072 hitch and I understand the hardware shouldnt be resued. Is there a part number for the hardware kit available? I cant locate it on the website.

asked by: Garth P

0

Expert Reply:

Yes, we have a replacment hardware kit available. You need to use part # RHK. On our product page, all you need to do is add the hitch model number and select the manufacturer in the drop down window. Then add to cart. Orders 1 kit.

expert reply by: Jared P

0

Answer 1

Yes, we have all of the hardware you will need to install the Curt 11829 hitch. You will want to go to the right hand side of the product page for the Replacement Hardware Kit for Trailer Hitches item #RHK you were looking at. You will see an…

view full answer...

Answer 2

The same part reference #RHK is used for many different Replacement Hardware Kits for many different brands and models of trailer hitch. The kits can include bolts, nuts, spacers and a bolt leader (fishwire) for installation. When ordering one of…

view full answer...

Answer 3

Yes you can order replacement hardware with #RHK for the Curt hitch 13306 which is now part #C13397.

view full answer...

Answer 4

The best hitch for the 2022 Jeep Compass is going to be the Curt Trailer Hitch Receiver item #C13363. The Curt Trailer Hitch Receiver item #C12174 you were looking at has a 1-1/4" receiver. You are going to want the 2" receiver as…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Replacement Hardeware Kit for a Curt Receiver Hitch.

Product Page this Question was Asked From

Continue Researching