Will this Curt Trailer Hitch # C11317 Work with my Aftermarket Exhaust On my 2010 Subaru WRX
Question:
I have a 2010 Subaru WRX 4-Door Sedan with dual tip aftermarket exhaust. The name of my aftermarket exhaust company is SPT Subaru Performance Tuning. I was just wondering if this hitch would still be able to bolt on and if it requires drilling. The aftermarket exhaust tips are larger than the stock exhaust tips.
asked by: Frank
Expert Reply:
The aftermarket exhaust tips should not interfere with you being able to install this Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11317. What would cause problems would be if the aftermarket exhaust had mufflers that were larger in diameter than the stock mufflers.
The # C11317 does require some minor drilling for installation, but with a decent drill and drill bit you should not have a problem installing this hitch.
You may need the following items to complete your towing setup:
Tow Ready Custom Fit Vehicle Wiring for the 2010 Subaru Impreza, part # 118464
Sportframe Drawbar 4" Rise 2000# Kit, part # 3594
Hitch Ball with 2" Diameter and Short Shank, 3,500 lbs GTW - Chrome, part # 19258
Hitch Ball with 1-7/8" Diameter and Short Shank, 2000 lbs GTW - Chrome, part # 19256
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Recommended Trailer Hitch Receiver for 2009 Subaru Impreza WRX Sedan with Dual Exhaust
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Will the Curt Hitch C13421 Interfere With the Lift Gate Sensor on a 2021 Honda Passport
- Q&A: Hitch Installation Instructions for 2012 Impreza Hatchback
- Q&A: Is Trimming Rear Fascia of 2014 Subaru WRX Hatchback Required
- Q&A: What Trailer Hitch Will Fit a 2011 Subaru Impreza WRX with Dual Exhaust
- Q&A: Hitch Receivers for a 2011 Subaru Impreza Sedan 4D?
- Q&A: Can I Use a 1-1/4" to 2" Hitch Adapter for a Folding Cargo Carrier?
- Article: Best Bike Racks for Electric Bikes
- Article: Performance Chips and Modules
- Article: How to Tie a Ladder to a Roof Rack