Kit Needed to Install Brake Controller in a 2000 Toyota Tundra with 4-Way

Question

Question:

I bought this Brake Force Brake control with the red,white,black and blue wires. I need all other pieces to do the install for the brake control. Do you happen to have installation instructions as well? I have a 2000 Tundra with the 4 prong trailer hook up.

asked by: John H

0

Expert Reply:

To install the brake controller you have on your 2000 Toyota Tundra will only require the part # ETBC7 that you referenced. This comes with everything needed to install the controller and adapt the 4-way to a 7-way.

I attached an install video that shows the # ETBC7 being installed on a similar 2002 Tundra as yours for you to check out as well.

expert reply by: Jameson C

0

Answer 1

If you installed a P3 brake controller #90195 in your vehicle and then went to tow a trailer with a 4-way connection the brake controller would not be in use at all so if you wanted to remove it from the vehicle at that time you certainly could.

view full answer...

Answer 2

There are no plug in adapters available for your 2013 Jeep Wrangler. In order for you to hook up your P3 brake controller you will need to do some hardwiring. If you have a 4-way connector on your Jeep, you can use a universal installation kit like…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Kit Needed to Install Brake Controller in a 2000 Toyota Tundra with 4-Way

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching