Hitch Rack for Elliptigo Arc Recumbent Bike on 2013 Toyota Prius V
Question:
I have a Prius V and an Elliptigo Arc bike. I will mount one of your 1 1/4inch hitches, but I want a rack that will support the bike frame in an upright, but diagonal position, thus keeping the bikes 6foot length within the confines of the narrower width of the Prius V. Thank you
asked by: Jerry E
Expert Reply:
The 1-1/4-inch hitch I recommend for your 2013 Toyota Prius V is Draw-Tite's Class I hitch # 24847. This hitch bolts on without drilling and offers a lower cost and freedom from the requirement to use a stabilizing strap, which is necessary for the Curt hitch # C11276.
We offer two bike racks for recumbent style bikes that will fit this hitch. Both are the platform style which carry a bike level. We do not offer any bike racks designed to suspend a bike diagonally.
The Elliptigo website does not specify the Arc's wheelbase or weight so you'll want to measure the distance between the two tires' contact points to confirm the best rack fit and make sure you select a rack with the appropriate weight capacity.
The Swagman XC-Extended Bike Rack for 2 Recumbent Bikes - 1-1/4" and 2" Hitches - Frame Mount # S64650-EXT handles bikes up to 35-lbs and wheelbases up to 69-inches.
The Saris Freedom Bike Rack for 2 Recumbents Bikes - 1-1/4" and 2" Hitches - Frame Mount # SA4412B-R handles bikes up to 35-lbs on a class I hitch that you would have and wheelbases up to 57-inches.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Swagman XC-Extended Bike Rack for 2 Recumbent Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Hitch Bike Racks
- Platform Rack
- Folding Rack
- Frame Mount
- Locks Not Included
- 2 Bikes
- Class 2
- Class 3
- Fits 1-1/4 Inch Hitch
- Fits 2 Inch Hitch
- Recumbent Bikes
- Swagman
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Replacement Hub Recommendation for Dexter Hub 8-250
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Q&A: Is Bow in 3,500 lb Trailer Axle Enough Camber for Loaded and Unloaded Trailers
- Q&A: How Much Upward Bend Should Trailer Axle Have
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Recommended RV Exterior Ladder for 22 Ft Thor Four Winds RV
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Where to Position the Trailer Axle?
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Rooftop Cargo Carriers
- Article: Best Bike Racks for Electric Bikes
- Article: Determining Trailer Tongue Weight