Recommended Dimension for Drill Mounting Holes to Mount Demco Actuator to Trailer Frame
Question:
I dont have any holes drilled on my trailer frame since the old actuator and hitch were welded. I am replacing an old Titan actuator. How far down on the three inch channel should I drill the mounting holes?
asked by: Mike W
Expert Reply:
I was able to go out to our warehouse and measure the Demco Hydraulic Actuator # DM72VR for you.
I found that the center of the mounting hole was 1-5/16 inches away from the master cylinder, so I recommend drilling the center of your mounting hole at about 1-1/4 from the top of your trailer frame.
It's also important to note that you will need to supply your own 1/2 x 4-1/2 Grade-5 bolts and it is recommended to use a steel bushing on the interior of the frame to protect it from any over tightening that can damage your trailer frame.
I've linked an installation video of this actuator being installed on a trailer for you to check out.
Product Page this Question was Asked From
Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Brake Actuator
- Surge Brake Actuator
- Straight Tongue Coupler
- Bolt-On
- 7000 lbs GTW
- 2 Inch Ball Coupler
- Drum Brakes
- No Lockout
- Demco
more information >
Continue Researching
- Q&A: coupler
- Q&A: Do Free Backing Brake Assemblies Still Require Use of Manual Lock Out on Actuator
- Video: Review of TorkLift RV and Camper Steps - Truck Camper Steps 3 Step - TLA7503
- Shop: TorkLift GlowStep Camper Scissor Steps - 4 Steps - Aluminum - 18" Wide - 375 lbs
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Video: Demco Hydraulic Brake Actuator Review
- Shop: Brophy Camper Scissor Steps - 4 Steps - Aluminum - Diamond Tread - 17" Wide - 250 lbs
- Shop: Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10" - Left/Right Hand - 3,500 lbs
- Video: Review of Demco Brake Actuator - 8K Surge Brake Actuator - DM8609101
- Video: Review of Demco Brake Actuator - Surge Brake Actuator - DM72VR
- Search Results: surge brake actuator
- Video: etrailer Left and Right Hand Hydraulic Brake Kit Installation
- Q&A: Replacement For Atwood 85091 Actuator as There Are Not Replacement Parts
- Search Results: brake line
- Search Results: dm72vr
- Shop: Kodiak Hydraulic Brake Hose - FIF and 90-Degree Male Fittings w/ Stainless Flares - 1.5'
- Video: Review of HappiJac Trailer Jack - Replacement Circuit Board and Wireless Remote - LC733540
- Search Results: surge brake parts
- Search Results: akubrk~35
- Video: etrailer Trailer Brakes AKBRKR-H7-L Review
- Search Results: as25
- Q&A: How to Install the Brophy Camper Scissor Steps Part # AS24 on a Palomino Truck Bed Camper
- Shop: Dexter Zinc-Plated Brake Actuator - Drum - Multi-Fit Ball - Bolt On - 7,000 lbs
- Shop: Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3,500 lbs
- Q&A: Replacement Control Board for HappiJac Jack System with Corded Controller
- Q&A: Brake Assembly Recommendation for Boat Trailer That Allows it to be Backed up Without Brake Lockup
- Q&A: Torque Specs for Brake Assembly and Brake Actuator
- Search Results: break lines
- Shop: Trailer Wiring
- Shop: Trailer Hitch