Fit and Compatibility of Replacement Door Hasp for a 2000 Haulmark Trailer

Question

Question:

Would this match up to my 2000 Haulmark door hasp, Thank you for your help

asked by: Thomas P

0

Expert Reply:

The best thing to do to determine if this is the correct hasp for your 2000 Haulmark is to measure.

I have linked an image with the measurements of the Polar Hasp # 158-101 to this page for your convenience. The center on center mounting holes are 4-1/4 inches apart and the width of the entire hasp will be 1 inch.

If your hasp's mounting holes are 3-3/4 inches apart then you will want the # PLR258-101.

If neither of these match your dimensions, just let me know what you find and I would be more than happy to help you find the right part for your trailer.

I have linked the above mentioned parts to this page for your convenience.

expert reply by: Jackie C

0

click to enlarge

Answer 1

For your 2009 Haulmark trailer, I recommend the Replacement Hasp for Polar Cam-Action Latch Kits - 1" Wide - Zinc-Plated Steel #158-101 with bolt hole measurements of 4-1/4 inches on center or the Replacement Hasp for Polar Cam-Action Latch…

view full answer...

Answer 2

Replacement Hasp #PLR258-101 can be used as a stand alone item but it is a replacement for the hasp that comes with Cam-Action Lockable Door Latch Kit #PLR258-002. It does not sound like what you are looking for though. To determine if we have what…

view full answer...

Answer 3

I spoke to TRC and the gap/channel in the J-Channel Trim #362416-955 will measure 0.154" (diagram included). Though we have not done any installs with this as of yet, so no pictorial examples, there will be absolutely no issues with the…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 6

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Answer 7

For a replacement you need the Titan Zinc-Plated Brake Actuator #T2477600. This is the Titan Model 10 which is the same as the Dexter DX12.5 you currently have on your boat trailer.

view full answer...

Answer 8

Thanks for all of the dimensions you listed! Based on that the correct bearing kit you'd need is the #BK3-200.

view full answer...

Answer 9

For your 1993 Ford E350 Van the only style of trailer wiring we have is the kind that installs inline with the vehicle taillights like the T-One kit part #118343. With this kit you'd unplug your vehicle taillight connectors and plug this kit…

view full answer...

Answer 10

From the information that you have given, I suspect that you have some additional ground wires on your trailer. Without being there to actually see the trailer, my best recommendation would be to wire the connector as follows: Green to Green for…

view full answer...

Answer 11

Great news! We do have a hasp and handle keeper with the mounting holes 3-3/4 inch apart. The part number you are looking for is the #PLR258-101. I have linked it to this page for your purchasing convenience.

view full answer...

Answer 12

The Ford Transit if equipped with the factory tow package would have came with both a trailer hitch and trailer connector and they would both be located directly under the rear bumper so odds are you do not have either because they are not hard to…

view full answer...

Fit and Compatibility of Replacement Door Hasp for a 2000 Haulmark Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching