Installation of Waste Master RV Sewer Hose LC359724

Question

Question:

Dose the lc359724 come with the adaptor that will be glued onto your rv.

asked by: Rick

0

Expert Reply:

Yes, the camlock that is included in the # LC359724 will glue to your current sewer outlet with a few simple steps.

First, remove the cap from your existing fitting. Use a hacksaw to cut off the exterior bayonet tabs and then smooth the surface with sandpaper. Next, glue the camlock fitting onto your RVs outlet using ABS glue # A05-0303.

I have linked the Lippert Components Waster Master RV Sewer Hose to this page for your convenience.

expert reply by: Jackie C

0

Answer 1

Right now, the individual 1/2" x 2" bolts, cap screws, and split washers, for the B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3500 are only available as a kit with the replacement base #BWRVBK3500.

view full answer...

Answer 2

For your B&W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter - Dual Jaw - 20,000 lbs #BWRVK3400 that draw down bolt is 1/2" x 3-1/2". We don't have the factory bolt and washer replacement, but you can…

view full answer...

Answer 3

You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…

view full answer...

Answer 4

It sounds like you are referring to the Lippert Components Tote Tank Adaptor part #LC360789. This adapter can be installed on the end of the Waste Master RV Sewer Hose part #LC359724 and provide you with a bayonet style fitting. The Waste Master is…

view full answer...

Answer 5

When adjusting the arms of the #BWRVK3305, you have the option of setting up so the king pin will sit 3 inches forward or 1 inch forward of the axle. I'd set it up at the tallest height, 18-3/4 inches above the floor of the truck bed and 1 inch…

view full answer...

Answer 6

I reached out to my contact at B&W and they said that the B&W Companion Slider Gooseneck-to-5th-Wheel Trailer Hitch Adapter - Dual Jaw - 20,000 lbs #BWRVK3400 sometimes within the first use or two this happens if you haven't used grease.…

view full answer...

Answer 7

Mechanically speaking, electric brakes are simpler. They're easier to troubleshoot. They're quite a bike less expensive than hydraulic disc brakes. Disc brakes provide more efficient braking. If all in all, you're happy enough with the…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Installation of Waste Master RV Sewer Hose LC359724

Product Page this Question was Asked From

Continue Researching