Options for a 17 inch Pusher Electric Radiator Fan

Question

Question:

Is the d16919 available in a push fan?

asked by: Glenn C

0

Expert Reply:

Derale 17 inch electric fans # D16217 and # D18217 can be used as pusher or puller fans. They can be mounted on either side of the radiator, as a pusher or puller, without having to flip blades or switch motor leads. This isn't a 17 inch version pusher that has the shroud. I have also included a link to our help article on electric radiator fans for you.

expert reply by: Michael H

0

Answer 1

Customers are used to Class ratings on hitches when towing a trailer so the Class ratings on the transmission coolers are meant to coincide with the Class rating of the hitch on the vehicle. It helps as a guideline for choosing a transmission…

view full answer...

Answer 2

Towing will put an additional heat burden on both your engine cooling system and your transmission. A higher capacity radiator will certainly drop your engine temp when you're towing with your Dakota, but an easier and less-costly alternative…

view full answer...

Answer 3

Radiator fan #D18217 includes rods and pads for mounting whereas fan #D16217 includes a mounting kit made up of more pieces. I have included a picture that shows the mounting hardware included with each fan. The additional hardware included with…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Options for a 17 inch Pusher Electric Radiator Fan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching