Differences Between the Curt Hitches for the 2009 Toyota Matrix

Question

Question:

What is the difference between curt hitch c12221 and c12228 for a 2009 Toyota Matrix s

asked by: Mark A

0

Expert Reply:

The difference is the shape of the cross tube. The part # C12228 has a square shaped tube whereas the part # C12221 has a round shape. Typically the round tubes are less visible than the square ones.

expert reply by: Jameson C

0

Answer 1

On some models of the Matrix, the muffler heat shield is installed in such a way that it would be sandwiched in between the hitch and the underside of the vehicle. If this is the case, the heat shield would either need to be trimmed away or removed…

view full answer...

Answer 2

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 3

Curt's 1-1/4-inch Class II round tube hitch #C12013 is a confirmed fit on the AWD 2005 Toyota Matrix XR and XRS and offers no-drill installation. The hitch will bolt to the bottom of the car's frame rails using the included hardware. Heat…

view full answer...

Answer 4

All available hitches made for your 2007 Toyota Matrix XR include both Class I and Class II types in the 1-1/4-inch size. All are shown on the linked page. You'll notice all three options, parts # 24812, #C12221 and #C12013, share a very similar…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Differences Between the Curt Hitches for the 2009 Toyota Matrix

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching