P2 Brake Controller Recommendation for 2009 Hyundai Santa Fe and Mounting Angle Explanation
Question:
Im looking for a brake controller and they all talk about degreesinch as in 90 or 360 degrees or other, but I havent found a discussion about what that means and how I would pick one as the best controller for my application. Please advise.
asked by: Rod J
Helpful Expert Reply:
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes.
The P2 must be mounted on a level horizontal (side-to-side) plane and must be lined up with the direction of travel for the internal sensor to function properly. I attached a couple picture that should help illustrate how it has to be mounted. The reason for this is that the inertia sensor in the controller has to be lined up properly with the direction of travel for it to accurately sense decoration and apply the brakes properly.
You will need to start with a 4-way (if you do not have one). For that you would want the # 118258 since you have the tow package.
From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
Products Referenced in This Question
T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Replacement Hub for 2013 Wildwood 26TBSS Hub Drum with AL-KO 8700
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Comparing the Curt Q20 and the Curt A20 5th Wheel Hitches.
- Q&A: Which Nev-R-Adjust Brake Assemblies for Load Trail 14K Dump Trailer
- Article: Best Camper Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)