Replacement Hubs for a 2003 Venture Boat Trailer Model 2250 with 6-Lug Hubs

Question

Question:

I have a 2003 venture boat trailer model # 2250. I wanted to order complete hub assembly with bearings. The hub assembly currently on it has a 6 bolt pattern. Can you tell me what hub assembly that you carry that will work?

asked by: Jerry

0

Expert Reply:

I did a little research and found that your 2003 Venture Boat trailer model 2250 has a capacity of 2,250 pounds but the 6-lug hubs and bearing information I found indicate that it uses hubs normally seen on 5,200 pound axles.

Since you have a boat trailer you might be interested in Kodiak hub # KH42655S which is stainless steel so it won't corrode. It uses inner bearing 25580 and outer bearing 15123.

Another option is hub # 8-213-5UC1 which uses the same inner bearing but a different outer bearing LM67048. The outer bearing still fits the same spindle it just has a different outer diameter to fit the hub.

For EZ lube axles with grease fittings at the ends I recommend # 8-213-5UC1-EZ. Both this axle and # 8-213-5UC1 come with bearings, races, and seals. Kodiak hub # KH42655S does not so you would also need bearing kit # BK3-100 (1 per hub). This kit comes with a 2.25 inch inner diameter grease seal. If a 2.125 inch grease seal is needed use # GS-2125DL.

expert reply by: Michael H

0

Answer 1

According to my research, the Dico 15638 Braking Assemblies that you have now are 10" x 2-1/4" therefore the correct replacement for you will be the Hydraulic Brake Kit part #AKUBRK-35-D for single servo or part #AKFBBRK-35-D for free…

view full answer...

Answer 2

We currently have not had a Ford F-150 with the power outlet in the bed to test fit a bed mounted 7-Way #C57008. I see no reason you will not be able to still install the 7-way as there is a large gap which can be seen in the installation video which…

view full answer...

Answer 3

I have included a picture that shows the measurements needed for a spindle, bearings, seals, faces, and hubs. The spindle measurements are labeled A through F. A is the spindle shaft diameter B is where the grease seal sits C is where the inner…

view full answer...

Answer 4

I went out to the warehouse and took several measurements of Curt Hook with Spring Loaded Safety Latch #C81840 for you. I have included a picture showing the measurements.

view full answer...

Answer 5

The wheel bore can be an issue but the bigger concern I see right off the bat is that you have 5 lug hubs and want to use 6 lug wheels. Therefore, we need to get you the correct hubs first before you can address the hub bore difference. The good news…

view full answer...

Answer 6

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 7

As long as bearings on the hub you choose are compatible with the existing spindle on your axle, you can indeed change to hubs that have the desired wheel bolt pattern. The first step would be to confirm the dimensions of your spindles using an…

view full answer...

Answer 8

The Mighty Cord 5th Wheel/Gooseneck Wiring Harness w/ 7-Pole Connector - 7' Long #A10-7007 uses 10, 12, and 14 gauge wires. This gauge - between 10 and 14 - is fairly standard on 5th wheel wiring harnesses like this.

view full answer...

Answer 9

We don't have a 7-way splitter like the photo you sent. We instead for applications just like yours recommend using the Mighty Cord 5th Wheel/Gooseneck Wiring Harness w/ 7-Pole Connector - 7' Long #A10-7007 or the 10 foot long #A10-7010. This…

view full answer...

Replacement Hubs for a 2003 Venture Boat Trailer Model 2250 with 6-Lug Hubs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching