What is the Maximum Amperage Rating for Bulldog Winch Wireless Controller BDW20099

Question

Question:

How many amps is this system rated at?

asked by: Scott S

0

Expert Reply:

Bulldog Winch Wirelesss Controller # BDW20099 is designed for 2,000 and 3,000 pound ATV winches with off-center drums. These winches draw up to 120 to 130 amps at full load. So you would not want to go over 130 amp draw for this unit.

expert reply by: Michael H

0

Answer 1

The Bulldog Winch Trailer Winch #BDW15020 you referred to has the power unit over the motor, as I've pointed out in the accompanying photo. Because of that there is a specific cover you need, the Bulldog Winch Neoprene Cover - Truck Winch…

view full answer...

Answer 2

The Bulldog 4,400 winch part #BDW15020 that you have has the power unit over the motor so you would need the winch cover specifically designed for that, part #BDW20190.

view full answer...

Answer 3

The cover you would want is the part #BDW20046 which will fit the UTV winch part #BDW15022 which is dimensionaly the same as the standard truck winches.

view full answer...

Answer 4

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Answer 5

From what you described, your break away system is indeed wired properly. I did also include a wiring diagram and a review video of the Hopkins Engager Push-To-Test Trailer Breakaway Kit #20099 for you to check out as well. With that being said,…

view full answer...

Answer 6

Yes, when the pin on a breakaway system like the Hopkins Engager Push-To-Test Trailer Breakaway Kit part #20099 is pulled that then sends full 12 volt power to the trailer brakes. When power is sent to an electric braking assembly you may very well…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

What is the Maximum Amperage Rating for Bulldog Winch Wireless Controller BDW20099

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching