Where are the Attachement Points for Curt Trailer Hitch # C11290 on a 2003 Honda Accord

Question

Question:

Do the two cross bar ends attach to the frame or to the wheel well

asked by: Ed V

0

Expert Reply:

The furthest two attachment points for the cross tubing on Curt Hitch, # C11290, are in the trunk pan (where the spare tire sits) and not the frame. The attachment point for the bracket nearest the receiver opening is a tow hook near the center of the rear end of the 2003 Honda Accord. I have included a link to the installation details for this hitch below.

expert reply by: Michael H

0

Answer 1

To install the Curt hitch part #C11327 on a dual exhaust version of the 2006 Honda Accord Sedan really wouldn't be that much different than a single exhaust. We had a customer come back and write a review for this hitch and he mentioned that…

view full answer...

Answer 2

You are correct in how the Curt Trailer Hitch Receiver -Class I - 1-1/4" #C11290 is mounted. This hitch has been tested to hold a maximum tongue weight of 200 lbs and a maximum trailer towing weight of 2,000 lbs when loaded. A riding lawn…

view full answer...

Answer 3

Yes the Curt hitch part #C11290 that you referenced fits both the coupe and sedan models of the 2001 Honda Accord.

view full answer...

Answer 4

I managed to locate an online copy of the 2000 Accord Owners manual. On page 186, Honda states that the maximum towing capacity of the vehicle is 1,000 lbs and that the maximum tongue weight load (downward force applied to hitch) should be no more…

view full answer...

Answer 5

To find the trailer wiring connection point on your 2000 Honda Accord to install the Trailer Wiring Harness part #118336 you will need to Unscrew the knob securing the access panel on the driver’s side of the vehicle’s trunk. Remove the access panel…

view full answer...

Answer 6

There is not a 2 inch hitch available for your 2003 Honda Accord. The manufacturer doesn't make one because the frame can't handle most accessories that would be overloading the frame. The 1-1/4 hitch is even restricted to a class I so there…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Where are the Attachement Points for Curt Trailer Hitch # C11290 on a 2003 Honda Accord

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching