2007 BMW X3 Curt Trailer Hitch Receiver Class III Dimensions

Question

Question:

2007 BMW X3 Curt Trailer Hitch Receiver Class III Hi Can you please send me the full dimensions of a 2007 BMW X3 Curt Trailer Hitch Receiver Class III? Thank you in advance

asked by: Panos C

1

Helpful Expert Reply:

I attached a picture that has all of the dimensions of the Curt trailer hitch part # 13573 that you referenced.

I also attached an install video for you to check out as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I have a solution for you, but the Curt Class III Trailer Hitch, #C13029, that you referenced will not fit the 1997 Chevrolet K1500 truck. If your truck has the standard or step bumper, then the Curt Class III Trailer Receiver Hitch, #C13042, will…

view full answer...

Answer 2

The best option for a trailer hitch receiver on your 1989 Chevy K2500 long bed is the Draw-Tite Max-E-Loader Trailer Hitch Receiver #41524. I like this one because it is designed as a custom fit for your truck and the cross tube is mostly hidden. It…

view full answer...

Answer 3

I have a solution for you, but the Curt Multi-Fit Hitch #C13900 is not a confirmed fit on your 1992 F-150. If you have a standard bumper on your F-150 you can use the Curt #14001 and if you've got a deep-drop bumper you'll want to use the…

view full answer...

Answer 4

The Draw Tite hitch part #41524 is a confirmed fit for a replacement for your 1995 Chevy K1500 pick up truck.

view full answer...

Answer 5

The best way to tell if your 1989 Chevrolet K1500 is a Heavy-Duty (HD) or Light-Duty (LD) version would be to obtain your VIN and call the dealer as they would be able to tell you whether or not you have the HD or LD version. Another way to tell if…

view full answer...

Answer 6

We have hitches that fit your 1985 Chevy C10 that has a deep bumper with the Curt hitch part #C13099. Your setup would definitely not be too low to tow with. A rise ball mount would make up for a lower hitch as well. I attached a help article

view full answer...

Answer 7

I spoke with my contact at Curt about hitch #C13902. The overall width is approximately 41-1/2 inches. The bolt holes are approximately 39-1/2 inches apart on center.

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

2007 BMW X3 Curt Trailer Hitch Receiver Class III Dimensions

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching