Brake Controller and Weight Distribution System Recommendation for a 2010 Chevy Traverse
Question:
I need to purchase a brake controller for my 2010 Chevy Traverse w/factory tow package. I am thinking about the Prodigy P2 - not sure what wire harness is needed... will it be plug and play or do I have to splice wires? I look forward to your response. P.S. also looking for weight dist w/sway outfit... which do you recommend. Ill be hauling a 21foot hybrid 3300# w/2 axles.
asked by: Del H
Expert Reply:
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes.
To install this in your 2010 Chevy Traverse with a 7-way will only require the install harness # 3026-P. This adapter plugs into the 6-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
For a weight distribution system for a trailer that weighs 3,300 lbs loaded the Strait Line System part # RP66083 is going to be your best option. This system is good for tongue weights that are between 400-800 lbs like what your trailer would end up having and has the only sway control on the market designed to prevent sway before it starts.
Check out the help articles and picture I attached as well.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Strait-Line Weight Distribution System w/ Sway Control - Trunnion Bar - 8,000 lbs GTW, 800 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Fits 2 Inch Hitch
- Allows Backing Up
- 500 lbs
- 600 lbs
- 700 lbs
- Reese
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Replacement Hub for 2013 Wildwood 26TBSS Hub Drum with AL-KO 8700
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Comparing the Curt Q20 and the Curt A20 5th Wheel Hitches.
- Q&A: Which Nev-R-Adjust Brake Assemblies for Load Trail 14K Dump Trailer
- Article: Best Camper Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)