Brake Controller Install Harness for a 2003 Chevy Tahoe

Question

Question:

ANY SPECIAL EXTRAS NEEDED TO HOOK-UP- MY VEHICLE IS A 2003 CHEVY TAHOE. THANKS

asked by: Mike E

1

Helpful Expert Reply:

To install the P2 part # 90885 in your 2003 Chevy Tahoe will require the install harness part # 3015-P.

I attached an install video and help article that will walk you through the process. There are a couple under hood connections that will also need to be made.

expert reply by: Jameson C

1

Answer 1

There are actually a few connections you will need to make under the hood to get the brake controller and tow package fully functional on your 2003 GMC Sierra. Under the hood, on the drivers side towards windshield, there is a bracket you will need…

view full answer...

Answer 2

Your trailer should have an ID tag on the trailer tongue that lists the VIN as well as the GVWR (Gross Vehicle Weight Rating) which is the maximum the trailer plus its cargo can weigh. If the trailer doesn't list the GVWR on the ID tag, or if…

view full answer...

Answer 3

We have suspension enhancement that will help beef up the rear suspension of your 2003 Chevy Tahoe but nothing will give you more towing capacity than you have so you'll want to make sure you don't exceed your towing capacity. These kits will…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Brake Controller Install Harness for a 2003 Chevy Tahoe

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching