Would the Trailer Valet Fit on an Airstream Trailer

Question

Question:

wanted to see if you think theres room to mount/use/store on my airstream trailer. its pretty tight - see attached pics

asked by: Sean

0

Expert Reply:

It would take basically 8 inches of clear real estate on the trailer frame to be able to install the mounting bracket of the Trailer Valet part # STC-V211. It looks like you SHOULD be able to make that aspect work on your trailer but you also need to consider the overall size of the jack when on your trailer.

I attached a picture that has the jack's overall dimensions when folded up for you to compare to your trailer to see if it would fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Trailer Valet can indeed be used on either the right or the left side of the trailer. I've edited a photo for you showing this.

view full answer...

Answer 2

I went to our warehouse and took some measurements of the Trailer Valet 5X, part #STC-V211 for you. I have attached a photo of the #STC-V211 with the dimensions noted. From the top mounting bolt on the mounting bracket to the top of the handle it…

view full answer...

Answer 3

The Trailer Valet Swivel Jack and Trailer Mover, part #STC-V211 is extremely versatile and allows you to maneuver your trailer at sharp angles and in tight places as well. The STC-V211 also features the ability to use a higher or lower gear ratio…

view full answer...

Answer 4

You would have to mount the Trailer Valet #STC-V211 as far forward on the trailer tongue to be able to turn the jack handle without hitting the boat. Since the trailer valet sticks out further than a traditional jack you should not have a problem.

view full answer...

Answer 5

Assuming you use appropriately sized grade 8 bolts for the Curt Channel Style Adjustable Ball Mount #C45900 there isn't a particular reason you couldn't them and some lock nuts in place of the included pins and clips. Even though the Grade 8…

view full answer...

Answer 6

Yes, you can simply remove the Trailer Valet Swivel Jack #STC-V211 from its pipe mount by pulling the pin from the mount and it would slide right off. I attached a review video for you to check out as well.

view full answer...

Answer 7

It sounds like you are referring to the security bolt which is part 21b in the attached diagram. The security bolt was designed to keep the Trailer Valet part #STC-V211 in place when the device is rotated to the stow position, and as an extra safety…

view full answer...

Answer 8

The Trailer Valet 5X Swivel Jack and Trailer Mover - Topwind - 15" Lift - 500 lbs #STC-V211 doesn't have detailed dimensional drawings, so I went out to the warehouse to take some measurements for you. 1. The distance from the mounting…

view full answer...

Answer 9

I wasn't sure exactly what dimension you were looking for on the mounting bracket of the Trailer Valet part #STC-V211 so I attached a picture that has nearly every dimension for you to check out.

view full answer...

Answer 10

Yes, the handle on the Trailer Valet Swivel Jack and Trailer Mover, part #STC-V211, that you referenced can be turned so the trailer can be steered to make 90 degree turns so you will be able to maneuver your camper into a tight spot. I have included…

view full answer...

Answer 11

In regards to the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211, the distance from the bottom of the wheel or ground to the center of the mounting point is 11" while fully retracted.

view full answer...

Answer 12

The inner leg that actual raises and lowers the Trailer Valet 5X Swivel Jack and Trailer Mover - Item #STC-V211 has 15 inches of travel. The bracket height when fully extended is 24 inches measured from the center of where the jack pivots to the…

view full answer...

Would the Trailer Valet Fit on an Airstream Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching