Can Trailer Balls Be Bolted to CR Brophy # CM91 Clevis Mount
Question:
Can this be used on my factory installed trailer receiver and could 2 different size balls fit on this at one time?
asked by: Ray B
Helpful Expert Reply:
The Brophy # CM91 Clevis mount would fit in the factory hitch on your 2016 Outback, but the mount isn't designed to have a trailer ball (or two) attached to it. Also, there isn't enough room to the inside of the mount to accommodate the width of the two nuts that would be needed to secure the trailer balls in place.
Your best bet would be to purchase two separate ball mounts that are equipped with the proper size trailer ball. Each ball mount should have the proper rise/drop. I'll link you to an FAQ article that shows how to determine the proper rise/drop ball mount. For trailer balls, use # 19256 for a 1-7/8 inch ball and # 19258 for a 2 inch ball. I've also linked you to our selection of ball mounts. Once you determine the rise/drop you need, select the ball mount that would come closest to the needed rise or drop. You might not be able to find a ball mount that perfectly matches the rise or drop you need, but as long as you're within an inch to an inch and 1/2, you'll be fine.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Product Page this Question was Asked From
Brophy Clevis Mount for 1-1/4" Trailer Hitches - 3/4" Diameter Hole - 3,500 lbs
- Clevis Hitch
- Clevis Mount
- 1-1/4 Inch Hitch Mount
- 3500 lbs GTW
- 3/4 Inch Diameter
- Standard Shank
- Brophy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Wiring Diagram for Installing the Replacement Single Zone Thermostat for Dometic RV Air Conditioners
- Q&A: How Does the Westin HDX Headache Rack Install on a Truck
- Q&A: Tailgate Clearance with Tow Ready # 63058 Pintle Mount
- Q&A: Troubleshooting 3rd Brake Light Not Working on 2019 Mazda CX-5 After Installing Curt T-Connector
- Q&A: The Lights On My 2018 Mazda CX-5 GT Alternate With The Trailer Tail Lights When Pressing The Brake
- Q&A: Lumen Output of 10" Gustafson 12V RV LED Ceiling Light # GUS54FR
- Q&A: What Grade Bolts are Used for the Curt Trailer Hitch Receiver # 14001 for a 1999 Dodge Ram Pickup
- Article: Ram Trailer Tow Prep Package
- Article: Most Popular Wheel Bearings
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Charge a Trailer Battery While Driving: 3 Common Problems (And How to Fix Them)