Center Cap Recommendation for the Taskmaster Rim part # TA73VR

Question

Question:

I heard these rims are rated to a psi of 145 is that true? Does this rim have a 0 offset? Wonder how it would look with a chrome center hub/cap and lugs

asked by: Robert N

1

Helpful Expert Reply:

The PSI rating for the Taskmaster Rim part # TA73VR that you referenced is 145 psi. I confirmed this with my contact at Taskmaster. It also has a zero offset.

I attached a review video for this rim for you to check out as well.

For a chrome center cap to go along with this you would want the part # 425EZ.

I went out and grabbed both products and took a couple picture of them together for you to check out as well.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Here is a list of our 16" steel trailer wheels which have the 6 on 5-1/2" bolt pattern. We will not have any wheels which have the 95.4mm pilot hole you are needing which should not likely be an issue since trailers will typically use a…

view full answer...

Answer 2

The Trailer King RST are a pretty middle of the road tire, not bad but not a top of the line tire. On the other hand the Kenda Loadstar ST tires are a high quality tire designed and strenuously tested in Ohio to make sure the tires are as reliable,…

view full answer...

Answer 3

You are correct the Bearing Kit #BK3-110 does contain the correct bearings, races and grease seal for the Dexter Axle #7461121-EB. But this does use the Spindle Nut Kit #RG05-100. You can order all the parts separately if you wish so you do not have…

view full answer...

Answer 4

Yes the Dexstar Steel Spoke Trailer Wheel #AM20741 is the same as the 17-243 that you mentioned so this would be an exact replacement.

view full answer...

Answer 5

The offset of the Taskmaster #TA73VR Steel Modular Trailer Wheel is zero. This places the mounting pad of the wheel (surface that contacts the hub) halfway along the width of the wheel.

view full answer...

Answer 6

Nearly all trailer wheels have a zero offset and the ones that don't have an offset that is very close to zero. For example the 16 inch trailer wheel part #AM22658HWTB that you mentioned has a zero offset. This is a 16 inch trailer wheel that is…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Center Cap Recommendation for the Taskmaster Rim part # TA73VR

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching