Trailer Hitch and Wiring for a 2012 Acura TL
Question:
It looks like the curt C11496 shows more of the hitch than the other curt, but it might just be the angle of the photos.
asked by: Greg W
Expert Reply:
I believe it is the angle of the photos because both Curt hitch # C11496 and Curt trailer hitch # C11496 will have the receiver and a good portion of the cross tubing exposed below the fascia on your 2012 Acura TL.
If you plan on towing with the Curt hitch then use # C45521 for the ball mount. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. Part # F-4 is the pin and clip you need.
If you will not be towing then I recommend Curt hitch # C11496 because it does not come with a ball mount you won't need and doesn't have special requirements for non-trailer loads like the Curt hitch.
For trailer wiring if towing you can use # 46255. I have included some links to videos and instructions for you.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Hopkins Active Tail Light Converter with Install Kit
- Trailer Wiring
- Trailer Connectors
- Vehicle End Connector
- Plug and Lead
- 4 Flat
- Hopkins
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Availability of a 5 on 4-1/2 Hub with a # LM11949 Outer Wheel Bearing
- Q&A: Do Trailer Tires and Wheels Need to be Balanced
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Q&A: Replacement Recommendation for TDE 46210 Hub
- Q&A: Recommended Cover for a Lance Truck Bed Camper Model 1010
- Q&A: Will the Demco Brake Actuator # DM8202022 Work with Disc Brakes on a Boat Trailer
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller Installation: Starting from Scratch
- Article: Best Bike Racks for Recumbent Bikes (2023)
- Article: Hitch Adapters and Extenders
- Article: Trailer Hitch Receiver Sizes