Are Computer Aided Design (CAD) Files Available for Timbren Trailer Axle-less Kit A20RS545

Question

Question:

Are 3D CAD models available ?

asked by: Chuck

0

Expert Reply:

Timbren does not publish CAD drawings for their suspension products like # A20RS545 but I do have a dimensional drawing that I have linked for you. This covers key dimensions and mounting hole spacing. If you visit the product page for this item and scroll down you'll find other helpful diagrams that will aid your installation.

Timbren's Axle-Less suspension units should be installed directly across from one another. Before mounting the units, measure back from the coupler and mark the frame to make sure that the two distance measurements are within no more than 1/8-inch of each other. Then you can drill holes through the frame and attach the hangers with Grade-5 half-inch bolts.

expert reply by: Adam R

0

click to enlarge

Answer 1

Hi Ruben; thanks for the question, and while there is one rack for your 2023 Ford F-150 with a 6-1/2' bed compatible with the Pace Edwards UltraGroove Metal Retractable Hard Tonneau Cover #PE66UV, it does not have sides, and is part #TX84NV.…

view full answer...

Answer 2

Off road tires tend to have a more aggressive tread pattern and can be wider/taller. Generally speaking most all trailer tires are regular tires. There are some turf tires and off road tires out there that would fall into this category but if you are…

view full answer...

Answer 3

The Timbren Axle-Less Trailer Suspension #ASR2KHDS09 you're looking at is actually not going to work with your trailer tires since this kit is only going to work with trailer wheels that are 16" or larger. So, instead I'd recommend going…

view full answer...

Answer 4

Since you want to use a larger wheel size you'd need to go with the higher rated Timbren Axle Less kit part #A35RS545. The wheel flange on the smaller hubs of the other kit can't accommodate the larger wheel diameters.

view full answer...

Answer 5

Our largest wheel and tire we carry I recommend using for the Timbren Axle-Less Trailer Suspension #A20RS545 is the Karrier ST205/75R15 Radial Trailer Tire with 15" Aluminum Wheel #KE27JR. This is our largest wheel diameter with the 5 on…

view full answer...

Answer 6

I reached out to Timbren about the Timbren Axle-Less Trailer Suspension part #A20RS545 and they stated that there are no minimum size requirements. That said, I personally would not run anything smaller than 10" so you don't have any issues…

view full answer...

Answer 7

The base on the #DM8550045 is completely different from the #DM8550046 so you can't simply add on the adapter for the recessed ball. However, you can swap out the base with #DM6316 and use your existing head which will save money over replacing…

view full answer...

Answer 8

All of the Class II ball mounts out there have a 3/4 inch diameter ball hole. It might be the best solution for you to replace the ball you have with one that will fit that ball hole size like what comes with the #36065 that you mentioned. For a 2…

view full answer...

Answer 9

While we do have a hinge that is going to let you have a gate that swings to the inside of the trailer and to the outside for a 270 degree swing, the hinges you referred to would not allow that type of movement. Instead, you will need what is called…

view full answer...

Answer 10

It looks like the closest thing that we have to that design is the Square Corner T-Strap Hinge w/ Reverse Bracket #PLR4040, but if that doesn't work we do have a wide variety of other hinge straps that may work for your application like the part…

view full answer...

Are Computer Aided Design (CAD) Files Available for Timbren Trailer Axle-less Kit A20RS545

Product Page this Question was Asked From

Continue Researching