Axle Rating for Timbren Axle Less System Explained

Question

Question:

is the load rating for the Timbren axles for each axle or for a pair of axles....like if it says it is rated for 5200 lbs, is that 5200 lbs for one axle meaning that a pair could handle 10400 lbs or for a pair of axles meaning that it takes a pair to handle 5200 lbs?

asked by: Thomas C

0

Expert Reply:

The weight capacity for the Timbren Axle-Less systems like part # ASR5200S01 is per axle. So if you used this on a single axle trailer you would have the axle capacity of 5,200 lbs.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

All of our trailer spindles are shown on the linked page, but none of these has a stub end to fit 2 x 3-inch tubing. All are either round like #TRU74FR or square like #TRU47FR. For a fabrication project like yours a better solution may be a bolt-on…

view full answer...

Answer 3

The recommended distance between the hangers of the #APS1 would be 24-7/8 inches when using the leaf spring #e54SR. When the trailer is set on the ground and the leaf spring is supporting the weight of the trailer the spring will flatten out and get…

view full answer...

Answer 4

If your Double-Eye Leaf Springs are 27 inches long, you will just want to mount the hangers in the Redline Single-Axle Trailer Hanger Kit #APS4 mentioned in your question about 26-1/2 inches apart. As a general rule, you want the distance between…

view full answer...

Answer 5

A leaf spring like the part #e57SR has a distance of 25-1/4 inches between the spring eyes. I did some checking and the hanger kit you would want is the Single-Axle Trailer Hanger Kit #APS4. And the distance between the spring hanger centers should…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Axle Rating for Timbren Axle Less System Explained

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching