Wiring Kit to Install Deka battery Isolator on a 2015 Toyota Tacoma

Question

Question:

Which installation kit do I need to install a battery isolator on my 2015 Toyota tacoma?

asked by: Allan

0

Expert Reply:

There isn't a special kit you would have to use to install battery isolator on your 2015 Toyota Tacoma unless it uses a Delco or GM CS alternator (which isn't likely). So you would use the regular kit, # DW08769.

expert reply by: Michael H

0

Answer 1

Since you will be towing a travel trailer, which is a static load that does not change weights all of the time, I recommend going with leaf springs, see link. If you have a 2 wheel drive model that is not a Pre-Runner, go with #SSA1 for 2,000 pound…

view full answer...

Answer 2

The Deka Battery Isolator #DW08770 is not vehicle-specific; it will work fine on your 1986 Dodge Ramcharger to protect the truck battery from excessive discharge and to regulate current in a multi-battery system. If your truck has a CS alternator you…

view full answer...

Answer 3

When installing Super Springs Suspension Enhancement, #SSA1, anything that that is in the area where the springs will mount will need to be relocated, if possible, so that the action of the spring does not damage it. I have included a link to the…

view full answer...

Answer 4

When installing the Deka Battery Isolator - 120 Amp #DW08771 you actually do not tap into the ignition systems. Instead you will run the wire from the alternator to the A post on the Isolator, then run a wire from the number 1 post of the isolator to…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Wiring Kit to Install Deka battery Isolator on a 2015 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching