Trailer Hitch Recommendation for a 2013 Infiniti G37 Sedan

Question

Question:

i need a trailerhitch for my infiniti g37 sedan 2013 but has to be class iii trailerhitch thanks

asked by: Frank D

1

Helpful Expert Reply:

The only trailer hitches available for your 2013 Infiniti G37 are Class I hitches like the Curt hitch part # C11499. Class III hitches are generally reserved for larger vehicles with higher capacities like trucks and SUVs.

expert reply by: Jameson C

1

Answer 1

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 2

The Curt Class I Trailer Hitch Receiver, part #C11499, is a confirmed fit for your 2008 Infiniti G35 Sedan and is a great choice for you. It has a 1-1/4 inch receiver opening, 2,000 pound weight capacity, and does include the drawbar, pin and clip. I…

view full answer...

Answer 3

For your 2012-2013 Infiniti G37 Sedan the Curt hitch part #C11499 that you referenced would be the hitch that you need. I attached an install video for you to check out as well. The best type of bike rack for beach cruiser bikes is going to be a…

view full answer...

Answer 4

You are correct in that the Curt Class I Trailer Hitch Receiver, #C11499, for the 2010 Infiniti G37 will have a max limit of 200 lbs of weight that you can carry on a cargo carrier. When looking at a cargo carrier you will need to factor in the…

view full answer...

Answer 5

The Curt hitch #C11499 that you referenced has been confirmed as a fit for your 2013 Infiniti G37 Sedan so it should work well for you. You should note that a towing setup is only as strong as its weakest component. While the hitch is rated for 2,000…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Trailer Hitch Recommendation for a 2013 Infiniti G37 Sedan

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching