Troubleshooting No Brake Lights Working After Hopkins Wiring Install # 46365
Question:
i hooked this harness #46365 up on my 2014 kia sportage. I have running lights and turn signals working. the 2 turn signal wires hook up on left side behind the bumper. and the running light wire behind the tail light. there are 3 other wires behind behind the tail light. i hooked the red brake wire from the converter to each of those wires and none of them was able to have the brake lights work. what do i need to do to get the brake lights working. thank you.
asked by: Rick V
Expert Reply:
You will need to use a circuit tester like part # PTW2993 to find the circuit that only sees voltage when the brakes are applied and use it for the stoplight circuit for the # 46365.
It sounds like maybe you haven't found the correct circuit to use yet and that is why the stoplights aren't working.
You should note that the recommended trailer harness is the part # 118526 that is a custom fit harness that would be much easier to install than the # 46365. I attached an install video
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Product Page this Question was Asked From
Hopkins Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- Hopkins
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Gooseneck Hitch
- Shop: Trailer Wiring
- Shop: Hopkins Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Video: Review of etrailer Trailer Fenders - Single Axle Fender - HP66VR
- Search Results: 12 inch wide fenders
- Video: Gooseneck Trailer Hitch Installation - 2006 Dodge Ram Pickup
- Shop: B&W Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches
- Q&A: How do I Tell if the Brake Controller is Bad
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Shop: Buyers Products 2-5/16" Fabricators Flatbed Gooseneck Hitch
- Shop: Single Axle Trailer Fender for Enclosed Trailers - Steel - 15" to 16" Wheel - Qty 1
- Shop: Single Axle Jeep Style Trailer Fender - Cold Rolled Steel - 10" Wheels - Qty 1
- Shop: Vehicle Tow Bar Wiring
- Q&A: Converter Recommendation for Combing Vehicle Turn Signal/Stoplights for Wiring Up Trailer 7-Way
- Search Results: trailer hitch wiring
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Ford Edge C89FR
- Q&A: Wiring Installation Instructions for Hopkins LED-Compatible Tail Light Converter # HM48895
- Q&A: Troubleshooting Absent Brake Signal with the Hopkins Converter # HM48895
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 44649
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Choosing the Right Trailer Wiring
- Search Results: 68149
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Fifth Wheel Hitch
- Video: Choosing the Right Brake Controller
- Shop: Brake Controller