4-Way Recommendation for a 2012 Chevy Silverado that has a 7-Way

Question

Question:

I have a 2012 chev silverado lt. my trailer connection is already on my bumper. I need a plug in which has the flat trailer connection on it can you help

asked by: Steve M

1

Helpful Expert Reply:

Sounds like you have a 7-way at the rear of your 2012 Chevy Silverado and are looking for a 4-way trailer connector as well.

For that I would recommend the Curt harness part # C55384. This will plug inline with the 7-way connector you have and will provide you with a 4-way while still keeping your 7-way functional as well.

expert reply by: Jameson C

1

Answer 1

You can use 7-way trailer wiring with the module part #PP20-702 to provide power to the third brake light of your camper shell/cap. Basically the stop/turn circuits of the trailer wiring need to run to the yellow wires of this module and then the…

view full answer...

Answer 2

If you install the Curt T-Connector Vehicle Wiring Harness #C55384 on your 2014 Ram 1500 you will get an additional 4-way that will have all of the taillight circuits isolated. Without knowing what you need them for that's all I can really tell…

view full answer...

Answer 3

What you need is the Curt T-Connector Vehicle Wiring Harness #C55384. This will plug inline with the 7-way you have at the rear of your 2015 Ford F250 and will give you an additional 4-way that you can then use for your camper.

view full answer...

Answer 4

If your 2015 Ram already has a 7-way trailer connector, you could install a 4 pole trailer connector by using the #C55384. You would unplug the trucks wiring harness from the rear of the 7-way and the #C55384 would plug inline between the vehicle…

view full answer...

Answer 5

We do have the replacement rubber strips for the Thule WingBar Evo crossbars, and like you said they are in fact different than the AeroBlade. The correct part for your WingBar crossbars is the following: - Replacement QuickAccess Interface Top…

view full answer...

Answer 6

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...

Answer 10

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

4-Way Recommendation for a 2012 Chevy Silverado that has a 7-Way

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching