How to Install Lippert Bolt-On Shock Mount Kit with Heavy Duty Gas Shocks for 2-3/8 Inch Axles
Question:
Hi, could you tell me how this product is installed?
asked by: Laura
Expert Reply:
I will be happy to explain how to install the shock kit # LC281255. In addition to the instructions below I have also included a picture of the actual instructions.
1. Raise trailer and jack up the axle to release pressure on the springs.
2. Remove old u-bolts and tie plate.
3. Install new tie plate with the longer side facing outward and torque the u-bolts to the specs in the instructions. NOTE: Do NOT reuse old components.
4. Compress the shock and make a mark on the inner shock where the outer shock stops.
5. Release compression. Measure the stroke and make a mark on the inner shock that is one half of the stroke length.
6. Measure the shock length when the shock is compressed to the halfway mark made in Step 5.
7. Lower the trailer back down onto tires and level so the equalizer(s), if equipped, are parallel to the frame and there is a full load on the springs.
8. Make a measurement perpendicular to the shock mounting lip on the tie plate that is the same distance measured in Step 6 + 2” and make a mark on the I-beam parallel to the shock mounting lip on the tie plate. NOTE: Mount shocks pointing outwards (away from the shackle kit, equalizer and/or center point) to get the best performance from the shocks. NOTE: Dry fit the shock to be sure it does not exceed a 45 degree angle or it will not function.
9. Align the bottom of the extended portion of the upper shock mounting bracket to the mark made on the I-beam in Step 8 and drill 11/32” pilot holes.
10. Use the 3/8” self-tapping bolts to secure the upper shock mounting bracket to the I-beam.
11. Remove nut, washer and rubber grommet from both sides of the shock.
12. Place the shock into the shock mounting lip on the tie plate and compress it to fit into the upper mounting bracket.
13. Apply the rubber grommet, washer, and nut (in that order) and tighten to secure the shock.
NOTE: Do NOT over-tighten. Tighten until the rubber grommet increases diameter equal to the washer.
Product Page this Question was Asked From
Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle
- Trailer Suspension Parts
- Leaf Spring Enhancement System
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Shocks
- Round Axle - 2-3/8 Inch
- Single Axle
- Lippert
more information >
Continue Researching
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 5,200-lb to 7,000-lb (3") Overslung Axle
- Shop: Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks - 3,500-lb (2-3/8") Axle
- Video: Review of Lippert Components Trailer Leaf Spring Suspension - Springs - LC281281
- Shop: Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 8,000-lb Axle
- Shop: Dexter Disc Brake Kit - 12-1/4" Hub/Rotor - Grease - 8 on 6-1/2 - E-Coat - 8,000 lbs
- Shop: Roadmaster Comfort Ride Add-On Kit for Triple Axle Trailers - 5,200-lb to 7,000-lb Axles
- Video: Review of Lippert Trailer Leaf Spring Suspension - Bolt-On Shock Mount Kit - LC281255
- Video: HydraStar Disc Brake Kit with Actuator Installation - 2017 Grand Design Solitude 5W Toy Hauler
- Search Results: trailer shocks
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 13" Hub/Rotor - 8 on 6-1/2 - 7K
- Shop: Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers - 5,200-lb to 7,000-lb Axle
- Video: Review of Hydrastar Trailer Brakes - Tandem Axle Disc Brake Kit with Actuator - HSE7K-T1
- Shop: Suspension Enhancement
- Q&A: How to Install Lippert Bolt-On Shock Mount Kit with Heavy Duty Gas Shocks for 3 Inch Axles
- Q&A: Which Direction Should Shocks of Lippert Shock Kit Point on Tandem Axle Trailer
- Search Results: trailer shock kit
- Q&A: Can Trailers Have Shock Absorbers Installed
- Video: SumoSprings Trailer Helper Springs Review
- Search Results: 3500 leaf spring
- Search Results: trailer shock
- Video: SumoSprings Trailer Helper Springs Manufacturer Demo
- Q&A: How to Position the Lippert Shocks on a Single Axle Trailer
- Video: Review of Dexter Replacement Bolt-On Shock Kit - K71-697-00
- Q&A: How to Measure for Adding Lippert Bolt-On Shock Kit for 3 Inch Axles to Trailer
- Q&A: Could Lippert Shocks # LC283280 FIt Morryde CRE300 Mounts on Trailer
- Q&A: Correct Shocks for a 2022 Jayco Eagle Fifth Wheel 321RSTS
- Search Results: sumo springs
- Search Results: rm~2450
- Search Results: timbren trailer
- Shop: Ladder Rack