How Does the Tether of the Camco Vented RV Bumper Cap w/ Tether # CAM40324 Attach

Question

Question:

how does the saver hook to bumper? do u have to drill a hole in bumper for a screw?

asked by: Bill

1

Helpful Expert Reply:

The "saver" portion of the Camco Vented RV Bumper Cap w/ Tether # CAM40324 that you referenced clips to the edge of the bumper that the cap is installed on. Basically you would push the clip over the edge of the bumper securing it, and then you would install the cap over it to secure it.

expert reply by: Jameson C

1

Answer 1

The friction sway control bars like the Reese Friction Sway Control Kit - Economy - by Draw-Tite, Reese and Hidden Hitch #83660 use a metal bar and friction pads that are tightened and adjusted to control the amount of movement against that force.…

view full answer...

Answer 2

If a trailer uses a friction-style sway control mechanism like #17200 it cannot be backed up until you disconnect or release the tension on that device. On the other hand, trailers with weight distribution systems that have integrated sway control,…

view full answer...

Answer 3

The benefits of an Equal-I-zer hitch over the e2 is primarily the improved 4-point sway control of the Equal-I-zer. The 4-point sway control utilizes steel on steel friction at the arms as well as in the hitch head to stop sway. The e2's 2-point…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 9

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

How Does the Tether of the Camco Vented RV Bumper Cap w/ Tether # CAM40324 Attach

Product Page this Question was Asked From

Continue Researching