Brake Controller And Wiring Recommendation For 2006 Chevrolet Express Van
Question:
What do I need to supply trailer lights and brAkes to this van? Was not eqpt from factory. I want easy install
asked by: Wen H
Helpful Expert Reply:
In order to add wiring and a brake controller to your 2006 Express Van, you will need to do some hardwiring.
If you have no 4-way connector, that is the first thing you will need to add to your van. I recommend the Tow Ready Custom Fit Vehicle Wiring, part # 118392. This is an easy installation by just plugging in the T-connector in the rear cargo area. This will give you a 4-way connector at the rear of your van.
You will then need part # ETBC7. this will plug into the 4-way and with additional wiring will give you a 7-way connector for your trailer at the rear of your van. When wiring longer vehicles you may need additional wiring like part # 10-2-1.
The brake controller I recommend is the Tekonsha Prodigy P2, part # 90885. This is our most popular brake controller because it is so easy to install and operate.
When working with electrical connectors I recommend using dielectric grease like part # 11755. This keeps dirt and moisture out of the electrical connections and helps prevent corrosion.
I have attached some installation videos you can check out.
Products Referenced in This Question
Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Wiring
- Wire
- Jacketed Wire
- 2 Wire
- 10 Gauge
- Deka
more information >
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Choose the Right Trailer Hitch Class
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Brake Controller Installation on 2016 Mercedes-Benz Sprinter
- Q&A: Tool for Adjusting Drum Brakes on Drop Axle
- Q&A: Does a 2022 Chevrolet Silverado 3500 Short Bed Need a Sliding 5th Wheel Hitch
- Q&A: Picking Between ETBC7 and ETBC7L for Brake Controller Install
- Q&A: What is the Difference Between a Class II and a Class III Hitch?