How to Determine What Replacement Hub and Drum Assembly with a 5 on 4-1/2 Bolt Pattern
Question:
If I have a trailer with a 5 X 4.5 bolt pattern can I buy a hub assembly with a 5 X 4.5 pattern and be confident it will fit?
asked by: Bryan L
Expert Reply:
The best way to determine the correct hub and drum assembly for your trailer with a 5 on 4-1/2 inch bolt pattern is to remove the hub from the trailer to get the measurements of your spindle. Or take a look at the inner and outer bearing numbers stamped into the sides of the bearings in order to determine the correct replacement hub for your trailer. Knowing the bolt pattern is a start, but not enough to determine the best replacement hub and drum assembly.
I have included a photo showing the places to measure. Using a tape measure or ruler will not be accurate enough.
The most popular trailer hub and drum assembly is the etrailer E-Z lube # AKHD-545-35-EZ-K and is for 3,500 pound trailer axles and bolt pattern of 5 on 4-1/2. The inner bearing is L68140 and outer bearing is L44649 which are commonly used. It also uses a # 58846 grease seal with an inner diameter of 1.719 inches. I added a video review for you.
I am including links to a FAQ page and a video that will help you when replacing the bearings, races, and seals on your trailer.
If you wish to provide your existing bearing, race and seal part numbers, I can double-check to ensure you are getting the correct bearing kit.
Products Referenced in This Question
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Article: Most Popular Wheel Bearings
- Search Results: lippert axle
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Search Results: akhd~545~35~ez~k
- Search Results: speakers
- Video: Review of Furrion RV Stoves and Ovens - Oven - FR74PR
- Video: Review of ABS Fasteners 1-3/4 Castle Nut Cotter Pin - 165649
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Shop: Furrion Electric RV Built-in Wall Oven - 20-11/16" Tall - Stainless Steel
- Shop: Furrion Over the Range RV Convection Microwave - 900 Watts - 1.5 Cu Ft - Stainless Steel
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Shop: Trailer Spindle Nut 1"
- Video: etrailer Trailer Suspension - Leaf Spring Suspension - APS4 Review
- Q&A: Replacement Bushing for Rear Hanger with Bushing 30-20
- Video: Dexter Heavy Duty Suspension Upgrade Kit Review
- Video: Review of Dexter Trailer Leaf Spring Suspension - HD Suspension Upgrade Kit Single Axle - K71-358-00
- Video: Review of etrailer 4 Leaf Double Eye Spring - e54SR
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Shop: Trailer Wiring
- Shop: Brake Controller
- Q&A: How to Determine Correct Leaf Spring Size on 6 X 12 Utility Trailer
- Q&A: Difference Between Dexter Hub and Drum Assembly 84546UC3-EZ and 84546UC3
- Q&A: Installing Bearing Buddy Bearing Protectors on EZ Lube Spindle
- Q&A: Trailer Brake Assembly Installation to Ensure Correct Side of Trailer
- Article: How to Measure a Trailer Axle
- Search Results: dexter electric brakes
- Video: Dexter Nev-R-Adjust Electric Trailer Brake Kit Installation
- Q&A: Preferred Method of Grounding Trailer Lighting Circuits
- Q&A: How To Attach A Ground Wire To Trailer Frame