Coupler Lock Recommendation for a 2015 Jayco White Hawk 27DSRL

Question

Question:

Will this work on a 2015 White Hawk 27DSRL

asked by: Russell

0

Expert Reply:

If the coupler on your 2015 Jayco White Hawk 27DSRL has a lip that does not exceed 3-13/16 inches and is not thicker than 5/16 inches the Gorilla Guard Coupler Lock part # 63228 that you referenced would work well for you.

Check out the review video I attached for more info.

expert reply by: Jameson C

0

Answer 1

I pulled up a picture of your 2015 Jayco Jay Flight 27rls and the coupler looks to be an underslung coupler like the part #CA-5335-B. Which then for a lock that is specifically designed to fit this type of coupler we have the part #AT89006 from…

view full answer...

Answer 2

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 3

The purpose of any lock is to keep honest people honest. If the potential thief is determined, any lock can be eventually defeated. The key is to make defeating the lock as difficult, time consuming and noisy as possible. The design of Gorilla…

view full answer...

Answer 4

Equal-i-Zer recommends to lube the friction surfaces regularly with the: -Equal-i-zer High-Performance Lubricant #EQ91-00-4250 for your Equal-i-Zer WDS, like the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control #EQ37100ET.…

view full answer...

Answer 5

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 6

You will have 2 choices that will fit your current travel trailer. The Equal-i-zer Weight Distribution System #EQ37120ET is rated for tongue weights of 800-1,200lbs and a trailer weight up to 12,000lbs. The Equal-i-zer Weight Distribution System…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Coupler Lock Recommendation for a 2015 Jayco White Hawk 27DSRL

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching