Size of the Opening of the Curt Quick Link # C82932

Question

Question:

Can you tell me the measurement of the link when fully screwed open?

asked by: Henry

0

Expert Reply:

I went out to the warehouse and pulled the Curt safety chain quick link # C82932 to measure for you. With the nut fully opened the opening is just at 5/8 an inch (0.625 inches).

expert reply by: Jameson C

0

Answer 1

On the B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package - Dual Jaw - 25,000 lbs #BWRVK3600, the moving components of the locking jaws need to be lubed but the pin does not need lube. These jaws are the only part of the hitch…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The Titan Hitch Box Extension and Reducer for 2-1/2" Trailer Hitches, #RP45292, is a confirmed fit for your 2012 Chevrolet Silverado 2500 HD short bed with a Lance camper. This extension is specifically designed for your slide-in camper with the…

view full answer...

Answer 9

The Reese Titan Extension/Reducer you referenced, part #RP45292 would work great with the 2-1/2 inch Class V hitch on your Ram. As you mentioned, the extension has a 8K capacity when cut down to the 24 inch length, that will provide a 2 inch receiver…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Size of the Opening of the Curt Quick Link # C82932

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching