Best Way to Install RV Trailer Hitch on I-Beam Frame with a 4 Inch Bumper Below on a 2014 Reflection
Question:
I believe this would work for me except that the 4 inch bumper is situated below the I-beam frame. Therefore the receiver would not pass under the bumper. Do you customize these hitches to fit? A bumper mount is not recommended on these trailers.
asked by: Everett H
Expert Reply:
The 2014 reflection by Grand Design model 337RLS with a 4-inch bumper you referenced won't work with Curt RV hitch # 13703 if you need something that drops down more than 4 inches. The reason is because the bracket won't go down far enough. See picture I included.
What you may be able to do is have a hitch fabricated using some of our fabrications parts. I have included a link to them for you to view. A local machine shop or a shop that works on trailers should be able to determine what additional parts are needed.
It's always a good idea that any welding should be done by a certified welder.
Product Page this Question was Asked From
Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide
- RV and Camper Hitch
- Frame Mount Hitch
- 22 - 72 Inch Wide Frame
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Bolt-On
- Weld-On
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide
- Shop: Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames
- Shop: Multi-Fit Motor Home Trailer Hitch, 47" - 71" wide
- Shop: Trailer Hitch
- Shop: Progressive Dynamics REL 60A 4500 Series Inteli-Power Converter Section
- Video: Ultra-Fab Products RV and Camper Hitch - Frame Mount Hitch - UF35-946403 Review
- Shop: Carrier Adapter Wiring Kit for Advent Air RV Air Conditioners
- Shop: Replacement Hawse Fairlead for Bulldog Winch ATV Winch - Long Drum - 6-1/2" Mount
- Q&A: Dimensions of the Brackets for Curt RV Trailer Hitch # 13703 and Will it Fit a 68.5 Wide Frame
- Q&A: Hitch Compatibility with Existing Sliding Bike/Cargo Rack on 2007 Keystone 290RKS 5th Wheel
- Video: Review of Draw-Tite RV and Camper Hitch - Adjustable Frame Mount Hitch - 82201
- Q&A: Welding Ultra-Fab Hitch to I-Beam Frame and Length of Receiver
- Q&A: Availability of Dimensional Drawing of Draw Tite Hitch 82201
- Q&A: Best Way to Carry a Generator on a Travel Trailer with a Hollow Bumper
- Q&A: Weld-On Tab Dimensions Of The Ultra-Fab 2" Trailer Hitch Receiver
- Q&A: What is the Adjustable Width on the Ultra-Fab 2" Trailer Hitch Receiver UF35-946403
- Search Results: keyless door locks
- Search Results: moryde
- Search Results: morryde
- Video: MORryde Tandem Axle Trailer Rubber Equalizers Manufacturer Demo
- Shop: Curt RV Bumper 2" Trailer Hitch Receiver
- Search Results: winegard
- Search Results: advent air rv air conditioners
- Video: Review of ASA Electronics Carrier Adapter Wiring Kit For Advent Air RV Air Conditioner - ACCARKIT
- Search Results: adjustable rv hitch
- Shop: Fifth Wheel Hitch
- Search Results: mount n lock
- Shop: Trailer Wiring
- Shop: RV Camera
- Video: Ultra-Fab Products Skid Wheels - Frame Mount - UF48-979011 Review