Weight Capacity of UItra-Fab # UF39-941707 Stabilizer Jack

Question

Question:

Will this product work with my 2015 Jayco 29XK motorhome as far as the weight capacity is concerned?

asked by: Terry

0

Expert Reply:

The Ultra-Fab # UF39-941707 could be used at the rear of your motorhome, but it's not meant to be used at the front. The 6000 lb capacity of the stabilizer jack can easily handle stabilizing the rear overhang of your Class C, but the front end would be too heavy.

Keep in mind, the stabilizing jack is meant to provide support, and not to lift the vehicle.

expert reply by: Mike L

0

Answer 1

The Ultra Fab stabilizer jack part #UF39-941707 draws 30 amps of 12 volt power so it would need to run off of the trailer battery and not any AC style of power source like what is found on house interiors.

view full answer...

Answer 2

The Rampage Clinometer with Compass - Analog #RA791006 will help you detect if you are on level ground or not with your RV, so it will absolutely be a help. It will only detect how level the ground is under your tires and suspension, so there may…

view full answer...

Answer 3

The only scissor jacks we carry are manual adjusting. The Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced would be an excellent choice for stabilizer jacks on your camper or RV as long as your frame width…

view full answer...

Answer 4

The Ultra-Fab Power Twin II Electric Stabilizer #UF39-941707 that you referenced is a stabilizer kit that has a motor on each side so that it stabilizes both sides of the trailer but it is sold individually. I attached a picture that shows what you…

view full answer...

Answer 5

The capacity of the Ultra Fab Power Twin Stabilizers part #UF39-941707 is 6,000 lbs which means it can support up to 6,000 lbs. So typically a camper weighs quite a bit more than that so you'd need to make sure you weren't supported the full…

view full answer...

Answer 6

I have confirmed with my contacts at Ultra-Fab and the weight of Ultra-Fab Power Twin II Electric Stabilizer for Trailers #UF39-941707 is 109 pounds. This stabilizer should be mounted directly to the frame of your trailer, and will work great along…

view full answer...

Answer 7

The Ultra-Fab Power Twin II Electric Stabilizer for Trailers and RVs - 22" Lift - 6,000 lbs #UF39-941707 you were looking at weighs in at 115lbs. This stabilizer is designed to fit trailer frames that are between 42" and 77" wide and…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 11

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Weight Capacity of UItra-Fab # UF39-941707 Stabilizer Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching