You can easily replace the thermostatically controlled RV ceiling fan you have in your 1999 Holiday Rambler Endeavor 37WDS with one that does not have that feature. We have the Ventline Ventadome Trailer Roof Vent part # V2094SP-28 which fits the standard 14 inch by 14 inch rough cut RV roof opening and has a fan without a thermostat. view full answer...
The Atwood Air Command Rooftop RV Air Conditioner w/ Heat Pump # AT15033-22 comes with everything you'll need to install it on your 2009 Holiday Rambler Endeavor that has the roof duct system already present. view full answer...
The ".c" you are seeing on the display of your P2 part # 90885 indicates that your controller is sensing a trailer connection. As long as you have a trailer connected when you see this it sounds like everything is fine.
If you see ".c." instead (note there is a second decimal point), then the controller senses a trailer connection and the boost feature is engaged. The boost feature means the braking power will come on a bit more aggresively. view full answer...
You have a Venture brand landing gear system so the correct repair kit for the lead leg is the part # LC146059 from Lippert. If you also need a kit for the follow leg you will need part # LC146060.
These kits include the drive shaft, bushings, E-Clip, drive pin, spiral pin, bevel gears, and shim washer. view full answer...
Yes, since your 2019 Holiday Rambler Vacationer 35P is built on the Ford F-53 chassis and it has a GVWR of 24,000 pounds the Roadmaster Reflex Steering Stabilizer # RM-RBK25-RSSA you referenced is the correct kit and it will work perfectly. This will do a great job of keeping the RV in line during travel by mounting between the steering mechanism and chassis and constantly working to maintain its position.
All the custom mounting brackets are included. I have attached a short video demonstration... view full answer...
I suggest the Adco Olefin HD All-Climate RV Cover for Class A Motorhomes, # AD74ZR. This is for Class A motorhomes up to 37 feet. The, # AD64ZR is for up to 34 feet and will work just fine with the attached ladder but if you have need extra fabric due to a satellite dish, then the 37 foot # AD74ZR may be a better option. Each option has cinch ropes at front and rear of cover to remove slack. view full answer...
To convert your separate brake light wiring on your RV to the combined signal needed for your RV trailer connector plug, I recommend the Roadmaster Brite-Lite Wiring Converter # RM-732. This will combine your turn and stop on the left and right sides to make it compatible with trailer connectors on the vehicle side of the connection.
If I misunderstood and your tow dolly needs the wires separated for separate brake and turn, then you will want the Vehicle to Vehicle Tail Light Converter... view full answer...
To add lock cores to your Thule Gutter Feet like part # TH65BJ you'd need the 4 pack of lock cores part # TH450400 which comes with everything needed to install them as well as two keys. view full answer...
For your 2009 Holiday Rambler Endeavor the Atwood AC Unit part # AT15028-22 would be a great option that will work well. It's ducted so it will fit right to your motorhome, it is rated at 15k btu so it has great cooling capacities, and it has a heat pump like you need as well. The drain system of this unit will match what you have on your motorhome as well. view full answer...
The Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers # RED87FR you asked from is not a direct fit for your 2019 Holiday Rambler Navigator 38K.
With the Redarc Tow-Pro Liberty Brake Controller # RED24FR for example you will need the Wiring Harness for Redarc Tow-Pro Liberty Trailer Brake Controllers # RED69FR and also the # ETBC7. You likely will need extra wire like # 12-2-1 sold by the foot. If you already have a 7-way then you will simply need # 5506 to add... view full answer...
We have a 100 foot roll of 3/4 inch wide RV Vinyl Insert Trim part # CAM25262 which I believe is what you are looking for. For black you'd want the part # CAM25272, for beige part # CAM25252 or for cream part # CAM25242. view full answer...
We don't have access to what the original equipment would be on your RV. Best option would be for you to get me as much info as you can on what the steps you have are. Can you get me any brand info and/or part numbers off of it? Pictures of the setup would be great too. view full answer...
Sounds like you are looking for something like the Wheel Masters 4-Hose Inflation Kit # WM8004. The straight hoses that come with this are 15 inches in overall length.
The hoses with 90 degree bends are 10-1/2 inches long.
I attached a review video for more info on this as well. view full answer...
I wish we could help with the battery you need but since the lithium version of the Goal Zero Yeti 400 is no longer made we can't get the battery replacement for it. Best option we have would be the lead acid battery version part # 287-23000. view full answer...
RVs like your 2017 Holiday Rambler Endeavor use double din sized stereos with multiple zones like the Jensen RV stereo part # JWM60A which would be a great solution. This has Bluetooth, USB, DVD player, and can be controlled from an app on your phone. view full answer...
The correct skid wheels for you will depend on the hitch tube diameter on your 2008 Holiday Rambler Augusta Motorhome. The Ultra-Fab Rotating, Hitch Mounted Skid Wheels # UF48-979014 are 4" in diameter, will bolt on, and work with motorhomes that are up to 30' long and have 2-1/2" x 2-1/2" square hitch tubes.
Another option is the Ultra-Fab Skid Wheels for Class C RVs up to 34' Long # UF48-979012 which are 5" in diameter and has brackets which weld onto the motorhome's frame before bolting... view full answer...
Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set # AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a 4 bolt pattern. view full answer...
We've had this question come up before and here's what Roadmaster sent me in response:
The axle bracket can be located on either the driver or passenger side and the tie rod bracket (B802) can be located on top or bottom side of the tie rod.
Orientation of the shock is not important, the unit can have the spring pointed towards the center of the RV or out towards the tire. Similarly, the eyelets on the shock unit (where bolts hold it to the brackets) can be located on both the top or... view full answer...
We have some faucets similar to the Phoenix Faucets 4" Dual Handle RV Tub/Shower Diverter Faucet w/ D-Spud - Chrome Finish # PF213364. When you say you want brass, I assume you want the underbody to be brass and we have one faucet that fits that criteria. It is the Phoenix Faucets 4" Dual Handle RV Tub/Shower Diverter Faucet w/ D-Spud - Chrome Finish # PF213332. All our other units use the plastic connectors. view full answer...