Expert Answers about Honda Pilot

• Why Does Trailer Wiring for 2004 Honda Pilot Route Through Back Door
• Having the 4-way run out of the back hatch is actually the preferred method although it seems like it wouldn't be. Having the 4-way stored inside the cab of the vehicle keeps it protected from rain and moisture to prevent corrosion and keeps it protected from damage to the wiring or connector by rocks or debris that might be on the highway. You can run the wire through the vehicle if you wish but just keep in mind that this does take more time and you may end up needing additional wire...
  view full answer...


• How to Fit 79 Thule ProBar Crossbars on a 2012 Honda Pilot with Factory Roof Rack
• To install the 79" Thule ProBar Evo Crossbars # TH713700 on the raised rails for your 2012 Honda Pilot you will need the Evo Raised Rail Feet # TH710401. Please note that you will want to make sure that these crossbars don't extend past your side mirrors as that's typically the what you will legally go by for max crossbar width. Please note that you will be limited to a 165 lb weight capacity so if you were to install 2 of the Thule Motion XT # TH629706 cargo boxes which weighs 42 lbs...
  view full answer...


• Installing Prodigy P2 # 90885 Brake Controller on 2015 Honda Pilot EX-L
• The P3 uses a different sort of bracket, that's more like a clip. The problem with mounting the mounting pocket using the hook and loop stuff is that it's not a tight connection. It takes a certain amount of force to operate the manual braking switch located on the underside of the Prodigy P2, not a huge amount of force, but enough to dislodge the pocket from the hook and loop fastener. Say the pocket has come loose, and is no longer pointed in the direction of travel. This means that...
  view full answer...


• Installing a Brake Controller from Scratch on a 2004 Honda Pilot
• You are correct, the ETBC7 does not come with written installation instructions because it can be used with so many different vehicles and brake controllers. But I will be happy to provide you with step by step instructions on installing the 7 and 4 Way Installation Kit, # ETBC7, on your 2004 Honda Pilot. I will also provide a helpful FAQ article and a video install of an ETBC7. The first thing you will need as you have pointed out is the correct 4-Way wiring harness if not already installed...
  view full answer...


• Installation of Tekonsha 4-Pole Trailer Wiring Harness Kit 118760 in 2016 Honda Pilot
• The Tekonsha 4-pole Wiring Harness # 118760 fits your 2012 Honda Pilot that has the factory tow package. The connector with the single blue wire plugs in to the mating vehicle connector, next to the main tow package connector behind the driver-side trim panel, but only if the vehicle has the back up sensors. If it does not then that wire/connector is not used. The written instructions for this item are linked for you.
  view full answer...


• How to Install the Yakima HalfBack Bike Rack Using the Top Straps in Anchor Mode
• The Yakima HalfBack 3 Bike Rack, # Y02633, will have to use the anchor mode when installed on the 2016 Honda Pilot. To switch the top straps from roof mount to anchor mode please reference the attached diagram. First at the cam buckle on the strap, depress buckle and remove strap that has the hook attached. Then take the end of this strap and run it through the center opening of the hook (step B & C). The hook end will rest inside the hatch of your Honda Pilot. Open hatch gate and then...
  view full answer...


• Can Trailer Wiring Harness 4-Way be Routed to Outside of 2004 Honda Pilot Instead of Through Hatch
• If you remove the flooring in the storage area in your 2004 Honda Pilot to get down to bare metal you may find a grommet through which you could route the 4-Way end of a trailer wiring harness such as # C55336. If there isn't one then a hole would have to be drilled, the wiring ran, then the hole plugged and sealed. I have linked a video showing an example installation for you.
  view full answer...


• Installation of Curt Front Mount Trailer Hitch Receiver on a 2012 Honda Pilot
• Installation of the Curt front mount receiver # C31064 for your 2012 Honda Pilot requires that the lower front fascia be permanently removed, not altered. I have included a picture that shows the part that gets removed both on the vehicle and after it has been removed. It is not a part that is visible. I have included a second picture that shows the hitch once installed on the vehicle. It will hang down maybe 3 inches from the bottom of the front bumper to the bottom of the hitch. I have...
  view full answer...


• Installation Instructions for Trailer Wiring on a 2014 Honda Pilot
• We don't have an install video for the wiring harness part # 118265 that you referenced. I attached a link to the install instructions for you to check out though. It will walk you through the entire process.
  view full answer...


• Are Fuses and Relays Needed to Use the Factory Tow Package Wiring on a 2009 Honda Pilot
• If your 2009 Honda Pilot has the factory trailer towing receptacle at the rear bumper then all of the tow package fuses and relays should be installed. You should be able to just plug your trailer into the receptacle and have all of the functions working except for the electric trailer brake function. If you have a trailer with electric brakes you will need a brake controller and wiring adapter to attach the brake controller in the cab of the vehicle. I recommend the Tekonsha Prodigy P2...
  view full answer...


• Replacing 27 Inch Wide Double ABS Sink With Stainless Steel Sink In Trailer
• I do have options for you in the Better Bath Double Bowl RV Kitchen Sink part # LC388412 for example which is 27-1/8" long x 16-1/8" wide x 6-1/4" deep and is made of 20-gauge stainless steel but I am not sure if you are going to find one with the exact requirements you have listed. That said, the depth of the sink and gauge of steel used would not really be an issue for most installations. The overall dimensions I also do not think there would be an issue with as most under-mount sink...
  view full answer...


• How To Install The T-One Wiring Harness On A 2019 Honda Pilot With Back Up Sensors
• The instillation of the T-One Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector Item # 118286 on a 2019 Honda Pilot is going to be the same as the 2017 and the 2020. The installers in the videos talk about the connector with the blue wire for the back up sensors. The difference between the video and your vehicle is you will be looking for a second plug to connect the blue wire with the white plug to. It will be in the same area as the first connector. The plug cannot...
  view full answer...


• Where it the Back-Up Sensor Plug on 2020 Honda Pilot for Installing Tekonsha 118286 Harness
• I can see why the instructions might be confusing and unfortunately we don't currently have an installation video of the # 118286 on a Honda Pilot with the backup sensor available, but I can help you. If you check out image D on the instructions page it shows where you should look to plug into the backup sensor. This plug is located behind the passenger side access panel. I've linked a photo of the instructions that shows this in better detail.
  view full answer...


• Color of Wires for Trailer Brake Controller Harness on a 2017 Honda Pilot
• According to pages 462 and 463 of the online version of the owner's manual for your 2017 Honda Pilot the 4 wires for the trailer brake controller connector are black, brown, violet, and green so it sounds like you found the correct connector. If it matches up to the Tekonsha Plug-In Wiring Adapter # 3070-P then you can definitely be confident that you have the correct connector. If you don't already have a brake controller then I highly recommend the Prodigy P3 # 90195 because it has...
  view full answer...


• Does P3 Brake Controller Require Fuse Installation on a 2015 Honda Pilot
• If your 2015 Honda Pilot came with the factory tow package that included a 7-Way trailer connector then the fuse for the brake controller may already be there. You can check ahead of time using the legend on the fuse panel lid. I checked the owner's manual and it is located in the sub fuse box in position 14. Check yours to confirm. The sub fuse box is the smaller one under the hood. Any brake controller is going to require a fuse or circuit breaker depending on the vehicle. If your Honda...
  view full answer...


• How Do I Know If My 2013 Honda Pilot Has Factory Tow Package
• If your 2013 Honda Pilot has the factory tow package you will find a connection point for the 4-way harness, like the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector # C56170, which you referenced, located behind the interior access panel in your rear cargo area. To install the harness will need to make two connections: The tow harness with 4-way connector plugs into the connection point behind rear bumper, driver's side (see S5). The converter...
  view full answer...


• Adapter Bar Needed to Carry Girls Bikes with Full Suspension on a Swagman Original Bike Rack
• Yes, there is an adapter that is used for the exact purpose of carrying alternative frame bikes. I recommend using the Swagman Easy Out Adapter Bar # 64005. This bike adapter bar will connect between the seat post and the handle bars, providing a horizontal cross-tube to secure the bikes in the rack. This will allow your girls bikes with full suspension, to mount in the your newly purchased Pro-Series Eclipse Bike Rack. Using this adapter bar will place the suspension below the mounting...
  view full answer...


• Wiring the 118491 Harness on a 2010 Honda Pilot
• First open the rear door and fold the rear seat forward. Locate and open the storage compartment on the drivers side of the cargo area. Next, locate the grey tow plug by opening the access panel inside of the storage compartment. Then insert the converter box into the vehicles grey tow plug. Next, locate the fuse panel in the rear cargo area on the drivers side next to the rear seats that you folded down. Open fuse compartment using a trim panel remover. Then insert the relays and fuses...
  view full answer...


• Is Torquing the Bolts For Hitch Installation Necessary If The Load is Light
• We do strongly recommend you torque the bolts as indicated by the installation instructions. This will ensure the safety of your bikes and everyone else on the road. In addition, should you ever sell your vehicle the next owner will be able to safely use the hitch for towing if desired. Chances are not torquing the bolts to their indicated rating may void the manufacturer warranty.
  view full answer...


• Fuse Location for Installing Trailer Wiring on a 2018 Honda Pilot
• I would be glad to help! When installing the Curt T-Connector # C56291 on your 2018 Honda Pilot, it looks like the location for the included fuse is the number 2 location in the fuse box that is located near the brake fluid reservoir (near the driver's side under your hood). If you check out the linked installation video on a 2017 Pilot you can see this being done. If you don't already have a trailer hitch and a hitch ball kit then I recommend the etrailer.com Trailer Hitch Receiver #...
  view full answer...