You're on the right track; this is the correct adapter, and the best place to look for the reverse light circuit when installing the Tow Ready 4 Pole to 5 Pole Trailer Wiring Adapter # 20036 is on the tail light assemblies on your 2018 Chrysler Pacifica. When installing this adapter, you may need to have a friend activate each function and test the wires using a circuit tester like the # PTW2992 to get the correct wire to tap into. view full answer...
For your 2017 Chrysler Pacifica the Draw Tite Hitch part # 36798 is a confirmed fit and would still allow you to use your hands free liftgate. At the very worst you might have to run your foot to either side of the hitch opening but it will still work just fine. This is a 1-1/4 inch hitch which would work just fine for you for a small trailer or bike rack, but since more accessories are made for 2 inch hitches and they have higher capacities I would recommend you go with the part # e98903... view full answer...
I have recommendations for you but unfortunately, you will not have a factory plug in under your dash nor will you have a factory 7 way or 4 way at the back of your 2006 Chrysler Pacifica. This is because a factory tow package is not available for your vehicle.
However, if you are looking for the proper wiring and brake controller to tow a trailer with brakes, I have the wiring you will need to do so.
First, for a brake controller I recommend the Tekonsha Prodigy P3 Brake Controller... view full answer...
Yes, the Curt 2 Bike Platform Rack for Fat Bikes - 1-1/4" and 2" Hitches - Frame Mount - Tilting # C18085-FB has a tilting feature that will allow you to open the rear hatch of your 2017 Chrysler Pacifica, even with the bikes loaded. I went ahead and attached the video that shows the functionality of the tilting mechanism. This rack will accommodate tires up to 4.88" wide.
We have another platform rack that tilts away with the bikes loaded, the Inno # INH120. However, this rack will only... view full answer...
Yes the etrailer trailer hitch # e98903 that fits your 2019 Chrysler Pacifica does come with all install hardware. I attached a copy of the installation instructions for you to check out as well an installation video on a 2020 for you. view full answer...
The etrailer.com hitch part # e98903 is a confirmed fit for your 2020 Chrysler Pacifica Hybrid and does have a couple extra steps for the hybrid models. There's an emissions canister that needs to be relocated temporarily when installing the hitch and also there are some holes on the driver side frame rail that need to be enlarged. I attached a diagram that shows this as well. view full answer...
If you have the factory tow package, installation of part # 42145 is very easy. There will be a connector on a wiring harness that will fit this part, it will be tucked up, maybe taped, somewhere close to the rear bumper. You will then attach the mounting bracket in a convenient location near the hitch, and it will hold the 7 way plug.
If you do not have the factory tow package, you will need the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55530. I've... view full answer...
I can definitely help you transport your kayaks with your 2017 Chrysler Pacifica but at this point in time (July 2019) there are no aftermarket roof racks that are compatible with your vehicle. I did check the online version of the owner's manual for your 2017 Pacifica and on page 175 is states that you have a weight capacity of 150 lbs so if you have 4 kayaks that weigh in at 38 lbs each that puts you at 152 lbs which means you are exceeding the max amount of weight for your vehicle. I... view full answer...
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118712 which is a fit for a 2019 Chrysler Pacifica will not have any effect on the vehicle's tail lights. Therefore, even if the in-line fuse on the power wire which leads from the converter box to the vehicle's battery blow, the vehicle's tail lights will still work just fine.
If you don't already have a trailer hitch picked out, the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C65CR is what I recommend... view full answer...
This is going to depend on a number of factors. The weight rating for your Pacifica (you would want to check your owners manual for your weight capacities), the weight capacity of your hitch and the weight capacity of your cargo carrier. I can give you an idea of what that will look like, but you will need to check the weight capacities of the products that you have for the definite answer.
For example, the etrailer Trailer Hitch Receiver # e98903 has a tongue weight rating of 400 lbs.,... view full answer...
When we installed the etrailer hitch part # e98903 on a 2021 Chrysler Pacifica like yours we found that it measured 5 inches from the center of the hitch pin hole out to the furthest point on the rear bumper. This will easily allow a Kuat NV bike rack part # NV22G to fold up as this bike rack has 7 inches from the pin hole center to the nearest portion of the rack when folded up. This means you'd have 2 inches of clearance to spare. view full answer...
I confirmed with Thule that you will need to use setting 10 for the FitDial on your Thule Gateway Pro 2 # TH88VR when mounted on your 2017 Chrysler Pacifica. view full answer...
For your 2017 Chrysler Pacifica, to add a brake controller when you don't have the tow package, you will need to start with a 4-way trailer connection. I recommend the Tekonsha Upgraded Circuit Protected ModuLite with 4 Pole Harness and Hardwire Kit - Includes Tester # C59496. This will give you the 4-way flat connector and then you will need the Universal Wiring for Brake Controller # ETBC7. This will give you the wiring, connectors, and circuit breakers needed to install your brake... view full answer...
Since you have a your Tekonsha P2 Electric Brake Controller # 90885, the wiring you need to complete your assembly with the 4-way currently on your 2017 Chrysler Pacifica is the # ETBC7. The brake controller will require wiring as well as circuit breakers, and the 7-way wiring connector for the upgrade. All of this is included in that kit. I've included the article that will walk you through your connection as well as a video to assist. There are 4 wires that come out of your controller... view full answer...
I attached a couple pictures that I took from the install instructions for the trailer wiring harness part # 118712 that is confirmed as a fit for your 2017 Chrysler Pacifica. In the instructions a trim panel remover tool like part # ALL648544 is recommended.
You will also need a Torx T27 socket wrench to remove the taillights.
It's the underside body panel that actually gets removed and not any of the interior pieces. view full answer...
The cold side of a brake light switch is used as the trigger signal to activate a trailer brake controller like the Prodigy P2 # 90885. The controller installation kit you purchased, part # ETBC7, includes a probe-style circuit tester that allows you to determine which of the wires at the brake light switch is connected the to cold side of the switch. The correct vehicle wire to connect to the RED wire on the controller is the one that goes hot ONLY when the brake pedal is pressed, and... view full answer...
The installation of the etrailer.com Trailer Hitch Receiver # e98903 will be the same as the Curt Trailer Hitch Receiver # C13383 for your 2019 Chrysler Pacifica Hybrid and I have attached the installation instructions of the Curt hitch for you so you can see exactly how to install the hitch on your Pacifica (the only difference between the two hitches is the matte black powder coat finish of the etrailer.com hitch compared to the gloss black powder coat finish of the Curt hitch).
The... view full answer...
When the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e98903 is installed on a 2018 Chrysler Pacifica, there is typically only going to be around 12" of clearance from the receiver to the ground (see demonstration video). It may be possible, however, I do not recommend trying to install this receiver without the use of a lift or jack as that would not leave a lot of room to work with and it could be dangerous.
You could use a kit such as 2-Ton Floor... view full answer...
I attached an install picture for the Draw Tite hitch part # 76046-SK that you referenced on a similar 2020 Chrysler Pacifica for you to check out. It's not a hybrid model in the picture but it would look the same on your hybrid model. view full answer...
Installing the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C29UR 2021 Chrysler Pacifica Hybrid will likely affect where you need to place your foot to operate the hands free lift gate feature, but after checking with Curt customers have not needed to replace the sensors.
You will just need to move your foot to either the left or the right of the receiver until you find the sweet spot for the sensors.
I included a link to the written instructions of the # C29UR for you... view full answer...