The Trailer Valet RVR9 Remote-Controlled Trailer Dolly part # TVRVR9 is designed exclusively for bumper pull trailers. It would not be possible to use this or really design one for use on fifth wheel and gooseneck trailers. The pin/tongue weight would be in excess of even the highest rated dolly and the length from the connection to the ground would be too extreme and create stability/strength issues. The tow vehicle is really the only option for maneuvering fifth wheel trailers view full answer...
If you checked the wiring for your left turn trailer stop signal and you are getting no signal directly out of the fuse box then you will want to replace the fuse on your 2015 Chevrolet Silverado 2500.
This will be the mini fuse in the 14 position in your engine compartment fuse block per your owner's manual. view full answer...
We have a Husky fifth wheel rail kit # HT31852-686 that fits your 2019 Chevy Silverado 2500 which you can use with your Husky slider hitch. view full answer...
Take a look at the video I have linked to the right. It shows installation of the in-bed wiring harness on a 2012 Silverado. The process will be essentially the same for your 2015 Chevy Silverado. You will need a 2 inch diameter hole. A hole saw drill bit is the ideal way to drill a large hole. This harness will fit your truck. view full answer...
To replace a skylight, you will follow the same installation as you would for a standard RV vent like # V2092SP-28. We do not have any skylight replacements available, but you will install a replacement using the Roof Vent Installation Kit - Sealant, Butyl Tape, Screws - White # 344270KITW. Screws and sealant will hold the skylight in place and make it weather tight. view full answer...
The wiring of the Lippert Components High-Speed Power Stabilizer Jack # LC298707 that you referenced is the exact same for if used at the front or rear of an RV. I attached a diagram that shows how everything wires up for you to check out as well as an install video link. view full answer...
The only time adding something like the MORryde X-Factor Crossmember # MR33WR would affect a warranty is if it caused some type of damage to occur to the trailer. This is essentially just more bracing to help stabilize your trailer even more so you don't have any reason to worry. view full answer...
You can install a brake controller like the Tekonsha Primus IQ Trailer Brake Controller # TK90160 and the plug in adapter # 3016 on your 2015 Chevrolet Silverado 2500, however it will still throw a code stating that the integrated brake controller isn't detected anymore.
You can clear this code by taking your truck to a dealership and have them reset your computer and remove the integrated brake controller, which will clear the code. view full answer...
For your Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider - Single Jaw - Underbed - 18,000 lbs # DM8550022 the Underbed Rail and Installation Kit for Demco Hijacker UMS 5th Wheel and Gooseneck Trailer Hitches # DM8551010 will work well. I've attached the installation details to help you determine the mounting to your frame which will then give you the correct bed locations. I've attached a drawing from the installation instructions as well as the complete instructions to assist. view full answer...
You can convert your B&W Companion # BWRVK3500-5W to be used in your new 2022 Chevrolet Silverado 2500. You won't have to buy a whole new hitch.
If you have the short/standard bed then you will want the Replacement Slider Base for B&W Companion # BWRVB3775 which will provide you with a slider base for proper turning clearance in a short/standard bed.
If you have the long bed then you will want the Replacement Base for B&W Companion # BWRVB3710.
You will take the head from your turnoverball... view full answer...
The Reese # RP30075 pivots 44 degrees front to back, and 5 degrees side-to-side, as confirmed by Horizon Global, who manufacture Reese products. view full answer...
The Edge Jammer Cold Air Intake # EP28248 referenced in your question does feature a pre-oiled filter which means that oil has been applied to the cones that run down the filter.
This allows the filter to catch more contaminants than a standard dry filter and will generally last longer but it will require some upkeep such as removing it every so often to clean it and reapply oil. I recommend using the Cleaning Kit # EP98800 for this purpose. view full answer...
Yes, the Redarc In-Vehicle BCDC Battery Charger # 331-BCDC1240D is designed to be specifically used with an alternator or smart alternator.
The battery charger will not necessarily put stress on your alternator, but rather optimizes the charge generated during driving in order to provide you with more battery power and capacity when you need it. view full answer...
You can hard-wire in a brake controller, and it seems that there are not a lot of the Sprinter 3500 models that are pre-wired, at least from what I've seen in my research. I have not seen any reports that this isn't possible, and we even have an installation video to walk you through the process.
The way to find out whether or not the plug is present by using a circuit tester like the # PTW2993 and testing for a hot wire when the brake is pressed- it's possible that one of the plugs that... view full answer...
The Redarc # RED44FR Tow-Pro Elite you mentioned includes a wiring pigtail that ends in bare wires, as shown in its product description photo. If you still have the plug in harness you used with your old Curt controller, you could simply plug it into the connector under the dash, then cut off the connector that used to plug into the Curt Controller. You'd wire those wires, color for color, to the wiring pigtail included with the Tow-Pro Elite.
If you no longer have the Curt harness, you... view full answer...
The hardware of the Erickson Over-The-Cab Truck Bed Ladder Rack # EM07707 that you referenced would not be considered temporary install hardware. As long as you install the rack according to the instructions it can be left on for as long as needed and you'd be totally fine.
If you really wanted to drill through the mounting brackets and then through the bed rail to really lock it down that is something that you could do but you'd end up permanently modifying the vehicle and rack, plus... view full answer...
The Gen-Y Hitch Shock Absorbing 5th Wheel-Gooseneck Pin Box, # GY58FR is a replacement for the Lippert 1621 and 1621HD pin boxes. It will mount using the hardware that is currently in place with the pin box you have installed on your 5th wheel RV. view full answer...
I took a look at the instructions (which I also linked for you below), and while there is no drilling into your truck's frame needed, depending on one factor, there may be some drilling required to install the Roadmaster anti-sway bar on your 2021 Chevy Silverado 2500, which is the following part:
- Roadmaster Rear Anti-Sway Bar # RM25FR
On page three of the instructions, it says: "On each side, remove the lower shock bolt and nut and loosen the upper nut to swing the shock out of the... view full answer...
I spoke with TorkLift, and while they do not have the specific measurements you're looking for, for the TorkLift Custom Frame-Mounted Camper Tie-Downs # TLC2223, they were able to tell me that from the frame of your vehicle to the end of the tie down will be 22".
For a complete set, you're going to also need the TorkLift Custom Frame-Mounted Camper Tie-Downs # TLC3215, as well as a set of turnbuckles # TLS9529-2-LK.
I have also included a couple of review videos as well for you to check out. view full answer...
The black wire of the # PK11893-11932 does carry the 12 volt power circuit. This circuit is a 12 gauge wire. The standard amperage rating for 12 gauge wire is 41 amps typically, but this harness has a 30 amp rating.
I attached a diagram that has a diagram for the wire of the connector. view full answer...