Whenever wiring Pacer Performance 3rd Brake Light Logic Module # # PP20-702 the yellow wires must go to each brake/turn signal and the green wire goes to the 3rd brake light. The reason why you need to hook both up is because the logic module filters out the turn signals and applies only the brake, so wiring only one may cause it to not work properly. view full answer...
Yes, the Tekonsha Primus # TK90160 has automatic, proportional braking. The trailer brakes are activated when the tow vehicle brakes are activated at the same intensity as the the tow vehicle. The Power Boost settings can be set for towing a variety of trailer weights.
The manual override switch is always available for emergency braking when the boost is not activated. The 3 boost settings are for when the trailer weighs the same, 25% more than, 40% more than, or over 40% of the tow... view full answer...
We haven't had the chance to install the Westin HDX Grille Guard with Punch Plate - Black Powder Coated Steel # W58RV on any vehicles yet, but there are detailed instructions included with the grille guard that walk through the steps and provide photos. I've linked instructions for a similar Westin grille guard to give you an idea of what to expect but it will likely require some trimming of the plastic fascia around the grille area and you'll bolt up directly to the frame at the front... view full answer...
So long as where you are mounting it allows the bracket to be secured on your front skid plate, it would be okay to do so on your 2019 Chevy Colorado ZR2. You will just want to ensure the wiring bracket isn't loose and can be properly positioned, but I don't see why you couldn't do this when installing tow bar wiring. For this I recommend an option from Roadmaster:
- Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267
I like this kit a lot as it is specifically designed... view full answer...
Yes the Hopkins Multi-Tow Trailer Connector Adapter # HM47675 could provide enough amperage for a Break Buddy assuming the power source it's plugged into also has enough amperage as well. view full answer...
When flat towing a vehicle you do not want your steering wheel to lock as this would cause your tires to drag any time you try to turn while towing. Placing your 2022 Chevy Colorado's transmission in neutral and then placing the ignition into ACC mode is not a step you can ignore. Failure to follow the steps listed in your owner's manual will result in damage to your transmission and/or more and likely not be covered under any manufacturer warranty.
Another step listed in the manual is... view full answer...
After 10 minutes of inactivity the Prodigy P3 part # 90195 will go into sleep mode which means it basically shuts itself off without losing presets. view full answer...
The Tekonsha Primus IQ Trailer Brake Controller # TK90160 does come with the wiring to connect to your 2017 Chevy Colorado. There isn't a plug and play harness, but your truck has the wires for the brake controller already run under your dash. I've attached a video of this installation for you to assist. view full answer...
The 2017 Chevy Colorado doesn't use a plug-in connector, but it does have a tow package wiring harness under the dash that the controller would wire directly into. The harness is located behind the driver's side kick panel. The controller would install as shown in the linked video. The pigtail included with the Curt # C24VV TriFlex brake controller would wire up to the tow package harness as follows:
• Tow Package Red/Green wire connects to Black wire from brake controller pigtail
• Tow... view full answer...
The Curt Triflex Brake Controller part # C24VV that you referenced has 9 different sensitivity settings so that you can adjust how aggressive you want the inertia sensor to react to deceleration. Since not all trailer brakes are as sensitive as others this allows you to tailor the braking to the trailer. So basically the higher the sensitivity the harder the brakes will apply with the same level of deceleration. This is also known as the "boost" setting as well. view full answer...
The wireless signal of the Demco Stay N Play DUO part # DM86VR that you referenced would easily work on your 37 foot RV. This system has a really great reception overall and we've not had any issues with customers who reported having problems. view full answer...
The Thule Xsporter, part # TH500XTB, can have its crossbars removed from the bases, leaving them installed and the bases clamped to the bedrails. I wouldn't recommend doing so, as you can also just remove the base's clamps and uninstall the entire unit in about the same amount of time as removing the bars. view full answer...
The Pop & Lock Remote Keyless Entry Kit part # PAL9000 is compatible with your Undercover LUX ABS composite hard tonneau cover. The Pop & Lock keyless entry part # PAL9000 kit comes with it's own key fob so you are not able to lock or unlock the cover with your Colorado's key fob. You are not able to use the truck's key fob because this particular Pop & Lock kit does not wire into your vehicle's power lock system. The kit replaces the latches of the Tonneau cover to allow the cover to open... view full answer...
The Roadmaster Automatic Battery Disconnect with Switch # RM-766 energizes to connect the battery for normal use. The current draw is a 12V quick-draw with 200-amp constant duty and 600-amp surge. I reached out to my contact at Roadmaster who confirmed this. view full answer...
Good news, I can help.
It looks like if you get the tow package on the 2015 Chevrolet Colorado the wiring for the brake controller is already run for you located behind the kick panel on the left inside of the driver's seat. See image I've attached for this location.
Our installer recommended trimming back the tape that was holding the wires so that it was long enough to work with the included 12-inch-long universal pigtail connector. See 2 minute 50 second mark of the video I've linked... view full answer...
It appears the wiring for the trailer brake controller is behind the drivers side kick panel on your 2011 Chevrolet Colorado. I have linked a video below showing the installation of the Tekonsha Prodigy P3 # 90195 on a similar 2015 Colorado. This will show you where the wiring is located for connecting your brake controller.
If your Colorado does not have this wiring I recommend using the Roadmaster Stop Light Switch Kit # RM-751442 as the brake switch itself is not usable. This kit includes... view full answer...
I'd be happy to help with the installation of your Kat's Heaters Custom Fit Engine Block Heater # KH11811 on your 2022 Chevrolet Colorado.
While underneath your 2022 Chevrolet Colorado on the back side of your engine block you will need to look for a cavity not all cavities will be on the back side of the engine block, but it will always be on the engine block. If you watch the video I linked below between 1:30 and 2:30 it will give you a general idea where the cavity will be located.
I... view full answer...
Installing the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells # Y01-140B is pretty straightforward in that you will install the rails by using a 6.5mm drill bit to drill holes in your roof and then after that it's a simple manner of securing everything down with the included parts. We do recommend using some form of sealant like the TremPro 644 # 0160297 to help keep water out of your camper shell.
We don't have any installation videos at this time, but we do have the installation... view full answer...
We don't currently have any videos of the Roadmaster EZ4 Base Plate Kit # RM-523182-4 but I have attached the Installation Details for you to take a look at.
The front fascia does need to be temporarily removed and there may be some trimming necessary. A 1-1/2 inch hole saw is also required. view full answer...
The Roadmaster Crossbar-Style Base Plate Kit # RM57VR for your 2021 Chevrolet Colorado, the manufacturer gives an estimate of 2.5 hours for a service technician to be able to install. As we have not been able to yet install this item ourselves on your Colorado I would estimate 3.5-4 hours for a typical do it yourself installer with some vehicle knowledge and all the proper tools.
This time may be extended as you will also be installing parts of the Roadmaster Towing Kit # RM-9243-1 for... view full answer...
Go To Results