The Malone Cargo12 # MPG901 will be able to fit onto your factory crossbars of your 2019 Audi Q5 as long as the crossbar width is between 1 inch and 3 inches and the height of the crossbars is between 3/4 inches and 1-3/8 inches. In order to know for sure if it will fit, I recommend measuring these dimensions of the crossbars on your vehicle.
As far as the Cargo12 allowing you to fully open your rear hatch, you will be able to adjust your crossbars in such a way as to give you enough... view full answer...
The Curt 13499 is no longer offered but Curt manufactures all of the etrailer hitches for us so you'd be getting the same thing with the # e94CR, with the only difference being that this hitch comes with a matte black finish. The fitguide can be a bit confusing some times, but the reason for the plug-in / no plug-in clarification is because on some vehicles there are fitment differences between these models. Since the system sections the vehicle this way you'll see the same hitch twice... view full answer...
It sounds like you have a classic ground issue with the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer part # C56404 on the 2016 Audi Q5. When the wiring harness does not have a good ground connection it will make the functions act erratically. Some functions will illuminate while others won't. I recommend to take a look at your ground connection and make sure it is attached to a clean bare metal surface of the vehicle's frame.
Also please keep in mind this wiring harness... view full answer...
I have a great solution for carrying your 2 kayaks. If you have a factory roof rack on your 2019 Audi Q5, you will not have enough weight capacity in order to transport the 40-pound (each pair) Thule Hullavators # TH898. I did some research on the weight capacity of the factory roof rack on your vehicle, and you only have 165 pounds of capacity. You will be at 80 pounds with the 2 Hulavators mounted, which leaves only 85 pounds for your 2 additional kayaks. Sadly, even if you have flush... view full answer...
Yes! I confirmed with the manufacturer for you the # e94CR is a fit for the 2021 Audi Q5!
Also wanted to mention if you're using it for towing, the correct trailer wiring kit is part # 119250KIT. view full answer...
The now-discontinued Prodigy RF you asked about can have serious issues pairing with European vehicles and while this used to be the only option for a wireless brake controller, that isn't the case anymore and I recommend an alternative that isn't going to have the amount of potential headaches.
So long as your 2014 Audi Q5 has the factory tow package the Curt Echo # C51180 will simply plug into the 7-way on the back of your Audi. There is no other wiring needed and the only other thing... view full answer...
The Yakima OnRamp Bike Rack # Y36FR requires 5" of clearance from the center of the hitch pin hole to the farthest edge of your bumper to fit properly. According to the different hitch fits we have available for your 2020 Audi Q5 this shouldn't be a problem but if you already have a hitch installed it would be a good idea to check out this measurement on your end just to be on the safe side of things.
If you don't already have a hitch installed I recommend picking up the etrailer Trailer... view full answer...
The Heininger PortablePET Twistep Hitch Mounted Step # HE3052 can be set to several different heights. This can be seen in the linked video at the :43-second mark. 4 bolts are used to set the platform height.
At the lowest height setting the TOP of the platform will be 6-inches below the BOTTOM of the receiver opening. I confirmed this with my contact at Heininger.
She also noted that the minimum recommended hitch height above ground is 16-inches. This is from the bottom of the receiver... view full answer...
I am assuming you mean it's hitting the rear hatch/trunk/lift gate when it's open but not when it's closed? Or is it hitting all the time? Have you tried reversing the Kuat Trio part # TR02 on the crossbars of your 2019 Audi Q5? view full answer...
The closest thing we have to what you're wanting is the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # 391AUDQ518T for your 2021 Audi Q5, and only because the hitch receiver or ball mount can be removed which leaves you with a completely clear rear bumper.
This would be ideal if you only planned on using your bike rack or towing once you get past your bad roads. Since it sounds like you'll be towing and using a bike rack while going over these bad roads you might consider... view full answer...
The Saris Bike Wheel Holder for Traps Single Track # SAWHL1 is intended for use with their Triple Track (parts # SATRK33 and # SATRK34) and Single Track ( # SATRK14) bike carriers. It is not meant for use on a vehicle's roof rack crossbars.
For a wheel carrier that can install on most aftermarket and factory roof racks you can instead use Thule part # TH98BV or Yakima part # Y02108. view full answer...
You do have the correct part to add the towing kit to your 2015 Audi Q5 to go with the Stealth Hitches rack receiver that fits your vehicle. The receiver and kit are the following:
- Stealth Hitches Hidden Rack Receiver # 391AUDQ509
- Towing Kit w/ Ball Mount and Trailer Wiring for Stealth Hitches Hidden Rack Receiver - 2" Ball # 391CONVR5
This kit will give you not only the ball mount but also the wiring to install a 7-way, and the 7-way is exactly what is needed in order to activate... view full answer...
The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e94CR is confirmed to fit your 2022 Audi Q5 PHEV. The installation of this hitch will require temporary removal of the bumper/fascia but does not require any trimming of the fascia.
I have attached the written instructions for your reference. view full answer...
Yes, it does. I checked with the manufacturer the etrailer Hitch item # e94CR is confirmed to fit the Sportback model of the 2022 Audi Q5. This hitch is custom fit and bolts to your Audi with included hardware.
If you are planning on towing you will also need a wiring harness item # 119250KIT and a ball mount kit item # C45534. view full answer...
The Rhino-Rack SRB Legs # RRSX031 are designed for other vehicles so you will need to use the Rhino-Rack SRB Legs # RRSX030 instead for the flush rails on your 2018 Audi Q5. To complete this roof rack system you just need the 49" Vortex Aero Crossbars # RRVA126B-2. I've attached an installation video and photo of this roof rack on a 2018 Q5 for you to check out.
If you let me know what you plan on using the roof rack for I'd be more than happy to make additional recommendations for you! view full answer...
Typically the factory roof rack set-ups are manufactured by another manufacturer and re-branded as Audi. Whether you would need an entire new set-up would depend on who manufacturers the Audi roof racks. Your best course of action for determining who makes the Audi roof rack would be to contact Audi. If you determine who manufacturers the Audi roof racks, I would be happy to help you determine if we have a solution to use your current towers.
Alternatively, the longest crossbars (50")... view full answer...
The correct Draw-Tite Max-Frame Trailer Hitch Receiver for a 2012 Audi Q5 is the part # 75940 which offers a bolt-on fit. It has a 2" receiver which will be great for towing or other hitch mounted accessories like bike racks and cargo carriers.
The Draw-Tite Max-Frame Trailer Hitch Receiver 75708 is no loner an active part number. view full answer...
In order to determine if you would have rear hatch interference on your 2015 Audi Q5 with the Thule Force XXL cargo box part # TH6359B you will need to take one simple measurement. You will need to measure from the center of the front crossbar back to the nearest part of your rear hatch when it is opened. If the dimension you measured is more than 58 the # TH626 will fit your vehicle without hatch interference. view full answer...
I do have an option for you but the Thule Hullavator Pro Kayak Carrier part # TH898 will not work with the factory crossbars you have on your 2015 Audi Q5 due to the lack of overhang. Instead, I recommend using the Malone DownLoader Kayak Carrier part # MPG114MD with the TelosXL Load Assist part # MPG351XL. The combination of this j-style carrier with the load assist will easily allow you to load your 14' long kayak on the roof of your Q5 with only one person.
As long as you kayak does... view full answer...
The Stealth Hitches Rack Receiver part # 391AUDQ518 which is a fit for a 2018 Audi Q5 will not require any cutting or trimming so long as you have the factory center knock-out panel. The 2018+ models should all have the factory center knock-out panel which will allow the hitch opening to show through without additional cutting. I spoke to my rep at Stealth Hitches to confirm this for you.
I have attached a photo to assist as well. view full answer...
Go To Results