I have an option for you but the Cruiser license plate holders that you looked at like part # CR21010 are not made in the USA. However, the WeatherTech brand of license plate holders are made in the USA.
I recommend the WeatherTech ClearFrame Chrome License-Plate Frame part # WT63023 but I did attach a link of all of the WeatherTech license plate frames available. view full answer...
According to Cruiser Accessories, their # CR76200 Tuf Flat license plate shield is designed to work with a license plate frame, so it'll work just fine with your existing frame.
If you don't already have mounting screws, you can use the # CR81300 set which includes security bolts that are very difficult to remove unless the included wrench is used. view full answer...
The Cruiser Tuf Flat Clear Shield for License Plates # CR76100 is designed to work well with or without license plate frames. Since it is flat and contours to the plate's surface it will work with most frames but in some cases you might need longer hardware for it to work with a particular frame.
I went to our warehouse to look at this item for myself. It measures 12 x 6-inches overall. There is a small lip on the shield that gives it a total thickness of about 1/8-inch. view full answer...
Yes, the Elite Stainless License Plate Frame part # CR21010 will absolutely fit both the front and rear license plates on your new 2018 Acura ILX. The U.S.A. uses a standard license plate size (12" long x 6" wide) so there will be no need to measure first. view full answer...
The backup sensors and camera on the Hopkins Rear View Camera # HM60195VA will prevent most aftermarket license plate frames from being able to be used. The plate will sit behind the notches in the camera and backup sensor mounts. view full answer...
The Tuf Flat Shield for License Plates part # CR76100 is not designed to be used on both sides of the license plate, only the front side. If you were to try and use this on the front and back then the license plate would not sit correctly and most likely would create a bunch of rattle. I am not aware of a license plate cover that is designed to go over both sides. If you then wanted to install a decorative frame like the Cruiser License Plate Frame part # CR20840 over the above then you... view full answer...
The Locking Fasteners For License Plates and Frames, # CR81200, is not a vehicle specific item, but it was designed for US domestic vehicles and motorcycles, so you should have no problem using this on your 2003 PT Cruiser.
These screws included with this kit have the standard diameter for license plate screws used in the USA. view full answer...
Some tow dollies like the Roadmaster Tow Dolly part # RM-2050-1 come with a license plate bracket. If the 2020 Master Tow Dolly did not come with a license plate bracket then you can use Trailer License Plate Mount Bracket part # LPL55CB. You will probably need to drill through the fender of the tow dolly or the frame to install it. The bracket does include a LED light to light up the license plate so you would need to splice the black wire into the running light circuit and ground the... view full answer...
At its longest and widest point, the Cruiser Accessories License Plate Frame, part # CR19003 measures13-1/2 inches long by 6-3/8 inches tall. Unfortunately, it looks like the frame would be a bit large to fit in the space you have available.
You can view our selection of license plate frames by clicking the provided link. view full answer...
The Cruiser Accessories Bubble Shield # CR72200 that you referenced is designed to fit over a standard sized license plate without a frame around it. If the frame was pretty flat and you had long enough screws to hold down the license plate cover and frame there's no reason you couldn't run the # CR72200 over top of the frame. It may not line up perfectly though. view full answer...
The only option I can think of is to custom mount your plate with a hinge. You could use a plate holder like # LP35BB or a metal plate like # CR79150 and mount it to the bottom of your trailer with a basic hinge like # PLR2008-AS. If you mount the hinge the correct way, it would allow swinging front to back without any friction and gravity would allow the plate to hang properly for travel. view full answer...
The thickness of the Pittsburgh Steelers License Plate # FPLC160 is designed to match what a standard license plate is. It would fit any standard license plate frame like what you have on your 2013 Cadillac SRX. view full answer...
To add lights and a license plate holder to your Swagman E-Spec Bike Rack for 2 Electric Bikes # S94FR you'll need the Thule License Plate Holder for Bike Racks # TH35JV and Curt Auxiliary LED Indicator Lights # C53201. The lights come with a 3M adhesive backing and can be stuck to the frame of the rack and plugged into a 4-pole connector on the back of your 2020 Ford Expedition. Most 2020 Ford Expeditions are going to come with aa 7-way so you'll most likely need an adapter # PK12716 to... view full answer...
I looked up pictures of your 2013 Keystone Passport 195RB and the taillights it has are the Bargman 92 series like the one you referenced so since you need the license plate frame and light the correct kit is the part # 30-92-003. view full answer...
The Cruiser Accessories Palm Tree License Plate Frame # CR19003 that you referenced is designed for passenger vehicle and will fit the standard size license plates you should have on your 2000 BMW 323i. view full answer...
I do have an option for you but there is not a good option for a license plate mount that will hook over one of the rungs of your ladder.
The only way to attach the a license plate to the ladder, is a bracket like part # A90416 and to use metal or plastic zip ties through the mounting holes to keep it secured to the ladder. view full answer...
The Draw-Tite Ultra Frame Trailer Hitch Receiver # 41947 is a confirmed fit for your 1968 Chevy C10 with standard bumper. This is an easy installation but will require drilling and the receiver will be below your license plate not behind it. . view full answer...
It sounds like you're trying to use the Hopkins back up sensor license plate bracket, part # HM60100VA, with a license plate bracket that has a back up camera? So you want to know if both brackets will work together?
It just depends on the foot print of the bracket you have on there now. It would have to fit in between the sensors on the Hopkins which are 10-3/8 inches apart. You also likely need longer screws to go all the way through.
Another option is to replace your camera with... view full answer...
Technically, the Star Pin Locking Fasteners for License Plates and Frames Standard # CR81200 are made for domestic vehicles like the Ford Fiesta, while Star Pin Locking Fasteners for License Plates and Frames Metric # CR81300 are made for import vehicles, such as your Subaru Crosstrek.
The main thing you want to look at is how the nuts are currently held in place on your vehicles. If they have a rectangular nut that is locked into a rectangular shaped housing then you will want to stick... view full answer...
Yes, The Eagle Motorcycle License Plate Frame part # CR77023 mounting holes measure 6" apart on top and 3" apart on the sides. The elongated holes themselves measure 1/2". view full answer...