The MORryde Wall RV TV Mount # MR23ZR has dimensions of 5.25" W x 5.83" T for the plate that attaches to the wall.
The MORryde Wall RV TV Mount # MR65ZR has dimensions of 10" W x 5.87" T for the plate that attaches to the wall.
Either one of these mounts will work with your Jensen LED RV Smart TV # ASA38VR (JE3221S) which has a 100mm x 100mm VESA mounting pattern. view full answer...
In regards to the Jensen LED RV Smart TV part # ASA38VR, the distance from the center of the upper mounting holes to the top of the TV is 9.18". I have attached a photo below which shows the dimensions indirectly with a bit of math. view full answer...
The MORryde Wall RV TV Mount # MR57RR weighs 16lbs. It can support a TV that weighs up to 20lbs.
The TV will need one of the following VESA patterns 100mm x 100mm, 200mm x 100mm, or 200mm x 200mm. Or you can use the VESA Adapter Plates # MR74RR to fit a mounting pattern up to 400mm x 400mm. view full answer...
With the MORryde Ceiling RV TV Mount # MR22ZR flipped down the space between the ceiling mounting bracket and center of the tv mounting bracket is approximately 9-1/2". When the flipped up the space between the two points is approximately 7-3/16" view full answer...
The bottom mounting holes for the Jensen LED RV TV - 1080P - 1 HMDI - 12 Volts - 24" Screen # JEN46VR are approximately 5" from the bottom the of the tv. The mounting holes are spaced 3.94" apart side-to-side and top-to-bottom. I can't confirm that another brands 12v cable will have the correct connection for the tv but I can confirm that the Power Adapter Cord for Jensen LED Televisions - 12V DC # DCCIG09 will work with this tv to power it through a 12v "cigarette lighter" port. view full answer...
I wasn't able to get my hands on the MORryde Counter RV TV Mount # MR42ZR or # MR62ZR to measure from the base to the bottom of the mounting plate, but I was able to get some dimensional drawings that show the distance from the base to the center of the mounting plate in their lowest and highest positions. view full answer...
In regards to the Jensen LED RV Smart TV part # ASA58VR, the distance from the center of the upper mounting holes to the top of the frame is 3.66". I have attached a photo blow with some more dimensions as well. view full answer...
I measured the Jensen RV TV with DVD Player - LED - 12 Volt - 19" Screen - AC/DC Power Adapter # JTV1917DVDC, with the leg stand and found it was 11-3/8 inches; It also measures 17-1/2 inches wide. view full answer...
Yes, it is. The Jensen LED 12V RV TV item # JTV1917DVDC has an HDMI port in the back which is what you will need to connect a Firestick or ROKU. You'll definitely need to use that HDMI extension cord that comes with the Firestick though. There's a short space between the port and the bottom of the TV. Not sure if the ROKU's include that piece so you may want to factor that into your decision of which one to use. view full answer...
I was able to get ahold of MORRyde for their technical drawings of the MORryde Ceiling RV TV Mount - Flip Down - Full Motion # MR24RR, and through that I was able to get some useful dimensions for you.
This mount has an overall height of 12.74" and measures 7.20" from the knob to the top of the ceiling mount; The plate has an overall measurement of 8" wide, 7" tall, and has an interior width of 5.99".
I have included a diagram depicting these measurements for you to check out as well. view full answer...
I contacted Jensen directly and they were able to verify that power cords for the Jensen LED RV TV # JTV1917DVDC are 72" long for the AC cable and 60" (give or take 2") for the DC cable. view full answer...
The SmartPlug RV TV/Internet Inlet # SM78VR measures 3-3/8" Wide x 5" Tall x 1-1/4" Deep but it also comes with a 1/4" thick gasket you put behind it so the depth could also be considered 1-1/2" when including the gasket. The mounting hole pattern is 2-7/16" x 2-7/16" as well. You can see all of this in the attached images.
This is also completely safe for marine use! view full answer...
Thanks for the measurements of your slide outs. For the 157-1/2" one you will want the Solera RV Slide-Out Awning item # LCV000168110 and for the 83" wide one you'll need the Solera RV Slide-Out Awning item # LCV000165062.
The item # LCV000165062 for your 83" wide slider is back ordered until the end of the year. If you have the clearance on either side you can use the larger Solera RV Slide-Out Awning item # LCV000168106. It fits slide-outs that are 86" - 91" wide and is 91" wide overall.... view full answer...
I contacted the distributor for the Greystone Curved Electric Fireplace # 324-000068 to obtain the dimensions of the rear of this unit so you will know the size opening required to install it in your new travel trailer. My contact advised that this unit requires a cutout that measures 26-1/4" wide x 5-3/8" deep x 20-1/2" tall.
This fireplace connects to your trailer's AC power outlet using a standard 3-prong AC cord. view full answer...
Unfortunately, we don't have any additional photos of the Malone Cargo Box # MPG902 that shows the mounting hardware as of yet but I can tell you the mounting points are adjustable. They're on tracks that can be spread apart from each other from 25 to 40 inches front to back. view full answer...