Each of the anchors in the BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets - Flush Fit - 1,000 lbs - Qty 4, part # BU22FR, are rated for 1,000 lbs. Please keep in mind these are not the anchors compatible with your 2019 Chevrolet Silverado 2500. The Bull-Ring Tie-Down Anchors for your vehicle are part # BU23FR. They are also rated 1,000 lbs per tie-down.
I have included a product description link below. view full answer...
The Extang CargoCleats Truck Bed Tie-Down Anchors # EX1932 have a 500 lb capacity. Additionally, the straps that are to be used with the tie downs need to have a high enough breaking strength capacity for the load you will be tying down, since the strap could have the lowest rated capacity of the whole tie down system.
I have included a link to a videos of the Extang CargoCleats Truck Bed Tie-Down Anchors, and to our selection of cargo tie down straps for you to select from. view full answer...
Yes, the BullRing Retractable Tie-Down Anchors for Truck Bed Stake Pockets - Flush Fit - 1,000 lbs - Qty 6, part # BU28FR, will fit your 2016 Ford F350. Each of these tie-down anchors are rated for 1,000 lbs. view full answer...
If the inner width of your flatbed trailer's stake pockets are 3-1/2" then you're going to want the Brophy Stake Pocket Tie Down Anchor item # TL2B you were looking at. The dimensions are 8-1/4" tall x 3-1/2" wide x 1-1/2" deep.
This tie down anchor will go through your stake pocket and will be secured by a pin that goes through the bottom. Each tie down anchor has a 4,000 lbs capacity. The Brophy Stake Pocket Tie Down Anchor item # TL2B is made in the USA and weighs 5 lbs. I have linked... view full answer...
The overall thickness, or diameter, of the Brophy D-Ring Tie Down Anchor # SR15-C is 3/8 of an inch.
I have added a diagram for you below showing all the measurements of the anchor; it is 2-1/4 inches tall and when mounted to the D-ring, the space inside will be approximately 1-1/2 inches. I have added a couple links below to video reviews for you to check out as well of the Brophy D-Ring Tie Down Anchor # SR15-C. view full answer...
WLL stands for Working Load Limit. The Erickson Stake Pocket Tie-Down Anchors # EM09085 that you referenced have a 2,000 lb working load limit when used as a pair. Working load limit means the amount of weight it can secure continuously. Some have a break strength capacity listed as well that is typically quite a bit higher.
For securing a 1,050 lb load these anchors would have more than enough capacity and would work well. view full answer...
I went out to the warehouse to measure the Extang CargoCleats Truck Bed Tie-Down Anchors, # EX1932. The anchor that I measured was just a touch under 6-1/2 inches wide.
Take a look at the attached videos so see more. view full answer...
The bolt that comes with the Brophy D-Ring Tie-Down Anchor with Backing Plate # DR1S has a diameter of 9/16 inches, so this would be the approximate size of the hole in the backing plate as well.
I have added a link to a video review for you to check out of the Tie-Down Anchor with Backing Plate # DR1S. view full answer...
The track of the Erickson O-Track tie-down anchors measure 2 inches wide and 1/2 inch tall by 18 inches long. This product would be a great choice for securing items in your truck bed. The anchors have a straight pull capacity of 733 lbs apiece and a side pull capacity of 583 lbs each.
I'll link you to a product video featuring the tie-down anchor system. view full answer...
I contacted Brophy, who said the distance from the bottom of the washer to the top of the Brophy D-Ring Tie Down Anchor # DR01 is 1-1/2 inches. view full answer...
I called Erickson and they do not offer a weight capacity rating for the Erickson Flip-Up Stake Pocket Anchors part # EM01006 but they did state that this particular tie-down is not really designed for heavy loads. If you do need to secure heavy loads then you will want to use the Erickson Retractable Tie-Down Anchors part # EM01003 which does have a listed weight capacity of 1,000 lbs. view full answer...
The CargoSmart Forged Steel D-Ring Tie-Down Anchor # 3481763 will require carriage bolts with a 3/8" diameter. The length of the bolt will depend on the mounting location and how much material you are needing to go through. view full answer...
You would want to use countersunk screws since the holes in the Erickson tie down anchors # EM09095 are countersunk. I went out to the warehouse and pulled one of these anchor sets to measure the diameter of the hole width for the head and threaded part of a screw. For the threaded part of the screw use a 5mm. The countersunk head can be as large as 8.75mm in diameter. A 9mm diameter head would be too large for the screw head to sit flush with the top of the anchor. view full answer...
I went out to the warehouse to measure the threaded length on the u-bolt included with Erickson U-Bolt Eye Tie-Down Anchor # EM53816. The threaded part is 3-7/16 inches long. view full answer...
The usable dimensions of the Brophy Stake Pocket Tie Down Anchor part # TL2B are 7-3/8 inches from the center of the pin hole to the plate that sits on top of the anchor, the width is 3-1/2 inches and the depth of it is 1-1/2 inches. This is designed to fit a standard 2 inch by 4 inch stake pocket. view full answer...
The Snap-Loc Single-Slot E-Track Bolt-On Tie-Down Anchor # SLSS measures 5-3/4 x 1 x 1/2 inches.
These single-slot E-Track Anchors are an ideal way to add additional single tie-down points to a trailer. The low-profile steel brackets can install on the ceiling, wall or floor of your trailer and can be inverted to provide a recessed tie-down point. They are rated for 3000-lbs each and are sold as single units. These are suitable for installation on any interior parts of your trailer... view full answer...
The CargoSmart Forged Steel D-Ring Tie-Down Anchor # 3481762 has a break strength of 15,000 lbs yes, but the 5,000 lb rating if the safe working load limit (WLL).
The difference between the two is the break strength is the point where the metal will break while the WLL is the number you want to keep your cargo from exceeding. The WLL is what the manufacturer has tested and approved the tie-down to be safely used at without any fear of the tie-down failing. view full answer...