Hi Charlie; For an AC unit that you can easily swap out with your Coleman-Mach ducted setup I recommend the Furrion Chill HE Replacement RV Air Conditioner # FR42PV. This comes with a wiring harness that lets you plug directly into your Coleman setup making for a relatively simple and easy installation. This unit has a 15,000 Btu capacity but it is also available as a 13,500 Btu with # FR82PV. If you would prefer it in black we have the # FR32PV and # FR62PV as well. view full answer...
Yes, the Voyager WiSight 2.0 Wireless RV Backup Camera System w/ Night Vision # ASA57YR would be able to splice into your running light circuit to power the rear camera, it even comes with butt connectors already on the wire harness to make integration with your factory wiring faster.
The monitor for this system can pair with up to four cameras so you could just get a second camera # ASA64YR to wire into the running light circuit on the truck camper and then move the monitor to whichever... view full answer...
The instructions for the High Pointe Over the Range RV Convection Microwave # HP44ZR are fairly vague when you consider not all RV manufacturers build campers the exacts same way. Some will have wood studs, others will have metal studs but it sounds like your 2006 Fleetwood Bounder 35E has a sheet of steel built into the walls. This would explain why your Sharp microwave mounting plate has so many screws holding it in. Your walls will likely still have some vertical metal studs behind the... view full answer...
Thanks for reaching out, Peter!
The Progressive Dynamics 4100 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel # PD4135K does have separate grounds for the AC and DC power sections. If you check out the linked installation video starting at the 20 minute mark you'll see how we wired in the power center. One of the bus bars is used for the AC ground and the other bus bar is used for the AC neutral and the DC ground. view full answer...
The correct front hitch for your Class C RV on the 2019 Ford E-350 Cutaway is the Draw-Tite # 65053. This is a custom fit application that installs using existing holes but it looks like you'll need to use some drill bits to make the holes a little larger, and you'll also need to cut some of the fascia at the front of your RV for this to fit.
The Curt Front Mount Trailer Hitch Receiver # 33055 you're looking at fits older models of the E-350 and won't work for your RV.
Attached is an... view full answer...
Hi Richard,
The arm length just dictates how far out the the awning can extend away from the trailer so you can still go with with smaller arms, you'll just likely have to fill in the old bolt holes from the previous arms. The Solera Smart Arm Electric RV Awning Conversion Kit # LC759405 is going to extend out 8' from the trailer. For the installation you'll want to pick up some butyl tape # AL28FJ and non-sag sealant # 344270341437-1 in order to prevent any water leaks. view full answer...
Trailer Valet created the XL Mounting Bracket # TVXLMB which will allow you to use their RVR's like the RVR9 # TVRVR9 and RVR12 # TV59FR you looked at without having to use the ball in the coupler. Instead you will remove the hitch ball and lower the trailer onto the RVR with the mounting bracket. This will allow you to align it to your hitch ball on your motorhome which is going to make it much easier for you. view full answer...
Hey Teddy, thanks for reaching out!
I recommend checking out the Curt Adjustable Width Trailer Hitch Receiver # 13703 which installed on trailers with a frame that is 22" to 72" Wide and is more of a universal fit.
I'm attaching an installation video for you to check out so you can get an idea of how this hitch installs to see if this is a good option for you. view full answer...
Hi Dane; to add a hitch for a bike rack to your Ford E-450 bus you can use the universal Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver. We have the # 41990-07 with 7" brackets and the # 41990-16 with 16" brackets. This is a weld-on installation so we recommend taking it to a certified welder. The hitch has a 2" receiver despite being Class V so it will work with most bike racks. view full answer...
Hey Roger, I attached a link to the install instructions for the Hollywood Racks RV Rider Bike rack part # HLY64FR that you have on this page as well as attached a review video that help visualize how it's used/installed as well. view full answer...
Sorry for the confusion on the details for the Tekonsha OEM Replacement Vehicle Wiring Harness # 22117 for your 2023 Toyota Tacoma. Since it can be used as a replacement for the OEM tapping into that connector is easier on those vehicles. Since you do not have the connector on your Tacoma you can simply use a Test Light # PTW2993 to find the correct wire on your brake switch which is on the brake pedal mount. Then you will be able to connect a controller like the Prodigy P3 # 90195. I personally... view full answer...
I have included an image below which shows the portion of the underbody panel which needs to be trimmed out for the Curt Trailer Hitch Receiver # C36RV to fit your 2024 Kia EV9 Light Long Range. This is found in the installation instructions linked near the bottom of the page so you can see all the steps required for installation if it is something you want to tackle yourself.
I have also linked the instructions for the Curt 4-Way # C66QV below if you should ever plan on pulling a trailer... view full answer...
Hey Don,
This isn't always the case for every adjustable-fit trailer hitch but Curt does require it with their # 13703. If you don't have a tie-down nearby to connect a strap to then you can use a stud finder to locate studs in the back wall of the RV and bolt on some anchors # 348825. I'd put like three or four anchors to give yourself a bit of adjustability when securing your load and then you can use ratchet straps, cam straps, etc. to wrap around the load and clip onto the anchor d-rings. view full answer...
The # TFR250SDJ is the right choice for your 2023 Ford F-250. The # TFRTT350J has a different design for severe service which would be something like a slide-in camper or salt spreader you're keeping in the bed of the truck all the time. The regular Timbren Suspension Enhancement System # TFR250SDJ is what you want for support while towing your 5th wheel in the summer.
I have attached an installation video below for your reference. view full answer...
Yes, you will be able to back your trailer into a tight campsite spot with the Curt TruTrack 4P Trailer Mounted Weight Distribution System # C74RV connected. Depending on the position your trailer will end up with the tow vehicle it may be easier to remove the weight distribution bars before to make disconnecting the trailer easier. view full answer...
Yes, it will so long as your 2020 Telluride already has a 4-way connector like item # C59236 or item # CU94FR. The 7-Way RV Upgrade Kit item # ETBC7L requires a functional 4-way to connect to your Telluride.
Please note that the 7-Way RV Upgrade Kit item # ETBC7L will only work with wireless brake controllers like the Curt Echo item # C51180. If you are planning on using a traditional in-cab brake controller like item # 90195 you will need to use the Universal Installation Kit item #... view full answer...
Looks like you're interested in a weight distribution system for your 2023 Subaru Ascent and possibly a hitch compatible with one. I took a look at your owner's manual (page 431) and if you have the factory hitch it isn't rated for one so the only option you have for it is the Curt True Course Advanced Bluetooth Trailer Sway Control - 1 to 4 Axles item # C94VV.
The Curt True Course item # C94VV is an electric sway control system that connects to your Subaru's 7-Way and is controlled by... view full answer...
Go To Results